147 1.6 Failed proxy after make windows anti-trap sensors.

[bubu321]

- I has error B1005/ B1006, not active windows anti-trap sensors.
- after doing windows anti-trap sensors procedure ( give complete signal ) must make proxy allignment.
- but procedure proxy alignment failed.

Code: Select all

Engine
Bosch Motronic Me7.3.1 EOBD injection (1 lambda)
ISO Code: 7C 86 8A 80 61

Body
Marelli Body Computer
ISO Code: 40 83 89 80 A1

Dashboard
Service Interval Reset
ISO Code: 32 83 26 85 B5

Driver's Door (TRW)
ISO Code: 86 07 02 19 FD

Boot (TRW)
ISO Code: 07 07 02 19 FE

COMPLETED

- test inside of FES.

Code: Select all

COMMAND: ATZ  RESPONSE:  ELM327 v1.4

COMMAND: ATI  RESPONSE: ATI ELM327 v1.4

COMMAND: ATE0 RESPONSE: ATE0 OK

COMMAND: ATL0 RESPONSE: OK 

COMMAND: ATH0 RESPONSE: OK 

COMMAND: ATSPC RESPONSE: OK

COMMAND: ATS0  RESPONSE: OK

COMMAND: ATCAF0  RESPONSE: OK

COMMAND: ATCFC0 RESPONSE: OK

COMMAND: ATCRA 7B0 RESPONSE: OK

COMMAND: ATSH 7B0 RESPONSE: OK

COMMAND: ATAT1 RESPONSE: OK 

COMMAND: ATST41 RESPONSE: OK

COMMAND: ATBI  RESPONSE: OK

This interface is compatible with ELM 327 1.4! Should connect properly with all CAN modules.

- try other interface ELM327 v.1.4, no good result.
- error log

• WARNING: This vehicle is properly configured. PROXI Alignment is not needed!
  EXECUTING ADJUSTMENT...
  Windows' Anti-Trap Sensors
  COMPLETED
  
  EXECUTING ADJUSTMENT...
  PROXI Alignment Procedure
  Writing CAN configuration data ...
  Writing to module: Body Computer Node (NBC)SUCCESS!
  0
  0
  Writing to module: Dashboard Node (NQS)FAILED!
  Writing to module: Driver Door Node (NPG)SUCCESS!
  Writing to module: Boot Node (NVB)SUCCESS!
  Writing to module: Climate Control Node (NCL)SUCCESS!
  FAILED TO EXECUTE

- next problem, after exchange dashboard VDO no communication to this instruments.
- but proxy alignment not working.

• Engine
  Bosch Motronic Me7.3.1 EOBD injection (1 lambda)
  ISO Code: 7C 86 8A 80 61
  
  Body
  Marelli Body Computer
  ISO Code: 40 83 89 80 A1
  
  Other
  Driver's Door (TRW)
  ISO Code: 86 07 02 19 FD
  
  Other
  Boot (TRW)
  ISO Code: 07 07 02 19 FE
  
  COMPLETED

[yani]

The PROXI function in 147 fails to configure the instrument cluster node.
This, however, is not a problem in your case as your instrument cluster does not need to be configured.

Please note that the automatic windows function will not work when anti-trap sensors don't work (or when you don't have anti-trap sensors at all).

[bubu321]

Code: Select all

after exchange dashboard VDO no communication to this instruments by CAN.

- this is problem because VDO realise this

Code: Select all

VDO ( MannesMan instrumental panel ) VDO Extra:

- inspection service value
- next service reset 
- Light setting corr.
- odometr km entry 
- dashboard replacement

[alfa156sarajevo]

Hi bubu321

I have almost the same problems as you regarding anti-trap sensors.
I turned on the function and tested a little bit…
Windows were working but only sometimes.
Sometimes they stuck in the middle, sometimes they would work just fine and for a while... And then they stoped...
I guess that I do not have those sensors installed.
I got the same errors like you…

So I turned off the function and delete the errors and everything is back to normal!

[bubu321]

@alfa156sarajevo

- and proxy alignment is working without error ?
( hm, AR 147 JTD )
- where is connector for this sensors.
- i will try connect 300 om, but don't know where is connectors.
p.s.
- must be between 1k2 - 1k9 and working.
- http://img585.imageshack.us/i/czujnikpoprawny.jpg/

[The-Kevster]

- and now it 's working.
- add emulator to anti-trap sensor socket.
--

Congratulations! Nice work.

Could you tell me what you did to emulate the anti-trap sensor and where I would find the socket? Currently both of my sensor voltages report 5v so I'm guess this isn't reporting correctly?

Thanks for your help!

[alfa156sarajevo]

@alfa156sarajevo

- and proxy alignment is working without error ?
( hm, AR 147 JTD )
- where is connector for this sensors.
- i will try connect 300 om, but don't know where is connectors.
p.s.
- must be between 1k2 - 1k9 and working.
- http://img585.imageshack.us/i/czujnikpoprawny.jpg/

NO! The PROXI is not working in all "Nodes".
As you already know that PROXI functions always fails at the "Dash Node" (dashboard).
So I just click execute the PROXI function and that is it!

I have no idea where are these sensors and connectors are. Maybe they should be in doors!?!
As soon as I get some time I will remove door panels and will try to find it...

[The-Kevster]

@alfa156sarajevo
I have no idea where are these sensors and connectors are. Maybe they should be in doors!?!
As soon as I get some time I will remove door panels and will try to find it...

No need to look in the doors. See here
viewtopic.php?f=4&t=1548&start=30#p5899