Hi Luca Rossi
Here also again, your board has no bridge resistor
I would ask at your first post already are
Which vehicle you would like to read?
Year of construction?
Control?
Your interface has no errors I can see
Greeting Eddy
Oohh, and what's my job with this? Change it or only remove? If i remove than connect the 2 sides of each other? Last question, when i use the MES i can do everything only in the ECU, in other modules all time writes for me: elm connection failed.... if its important its a 2003 Stilo 1.2.
Alfaeddy wrote:Hi Luca Rossi
Here also again, your board has no bridge resistor
I would ask at your first post already are
Which vehicle you would like to read?
Year of construction?
Control?
Your interface has no errors I can see
Greeting Eddy
car fiat punto 1.3mjt 2009
diagnosis engine
resistance bridge I had already removed the R27 facceva bridge between 6-14 plug eobd
the problem is that I can not connect to the interface multiecuscan and if I select the com port (assigned to the interface in computer resources) when I run the test me error:
COMMAND: ATZ
RESPONSE: ATZ
ELM327 v2.1
>
COMMAND: ATI
RESPONSE: ATI
ELM327 v2.1
>
COMMAND: ATE0
RESPONSE: ATE0
OK
>
COMMAND: ATL0
RESPONSE: OK
>
COMMAND: ATH0
RESPONSE: OK
>
COMMAND: ATSPC
RESPONSE: OK
>
COMMAND: ATS0
RESPONSE: OK
>
COMMAND: ATCAF0
RESPONSE: OK
>
COMMAND: ATCFC0
RESPONSE: ?
>
COMMAND: ATCRA 7B0
RESPONSE: ?
>
COMMAND: ATSH 7B0
RESPONSE: ?
>
COMMAND: ATAT1
RESPONSE: OK
>
COMMAND: ATST41
RESPONSE: OK
>
COMMAND: ATBI
RESPONSE: OK
>
WARNING: This interface is not compatible with ELM 327 1.3! Will not connect to any CAN module.
Hi Luca Rossi
A ELM327 v2.1 does not work with Multiecuscan
since there is no possibility
So I asked if there is a v1.5 or v2.1 a
You need to other ELM Interface
Greeting Eddy
Hi eddy this is azeem , I have the same problem as lucarossi with my elm327 v2.1 Bluetooth with multiscan and even all android obd apps it says unable to connect to ecu .
My car is fiat palio stile (facelifted) 1.6 16 v (Indian version) with 3 pin to obd converter ..
Any help ? What obd device I need and any chance getting elm327 Bluetooth to work on this car ?
Cheers
azzu wrote:Hi eddy this is azeem , I have the same problem as lucarossi with my elm327 v2.1 Bluetooth with multiscan and even all android obd apps it says unable to connect to ecu .
My car is fiat palio stile (facelifted) 1.6 16 v (Indian version) with 3 pin to obd converter ..
Any help ? What obd device I need and any chance getting elm327 Bluetooth to work on this car ?
Cheers
I believe that this vehicle use VAG/KKL. I also could not connect the MES with a Palio 1.5 1996
Hello everyone, I wanted to change the chip MCP2515 with a version V1.4 type the PIC18F2580, but this chip is not found in 18 feet to be welded, so I ask you, there is a chip in 18-pin compatible with version V1.4
lucarossi.1963 wrote:Hello everyone, I wanted to change the chip MCP2515 with a version V1.4 type the PIC18F2580, but this chip is not found in 18 feet to be welded, so I ask you, there is a chip in 18-pin compatible with version V1.4
Maybe not so simple just change the chipset, which can use a different circuit. Why do not you just buy a version 1.5 ???
Remove the Resistor in the red Frame
and you can read the CAN Bus Protokoll
of your Car
Greetings Eddy
The attachment IMG_0591 markiert.jpg is no longer available
Hello!
I have a ELM327 USB with PCB like in photo.
It connect only to engine ECU, not to other ECU.
I see my interface is similiar to Tasmo's one (viewtopic.php?f=5&t=1493&start=1680),
but it has more component on the right (in my photo) that weren't on Tasmo's PCB.
