FES won't connect with Adapter Cable 3

[Waltomatic]

I don't think... because when switch 7 is off, nothing is connected... I've made this connection to imitate adapter 1 for my alfa!

BUUUT you amended that wires together at some point, right?

[Waltomatic]

That's pretty confusing me... So why in my interface pin 12 wasn't connected from the beginning?

But it is just that: the interface reads the STANDARD and the pin 12 is not STANDARD (it's optional), so we do the "transcription" through the Adapter Cable.

[Waltomatic]

That's pretty confusing me... So why in my interface pin 12 wasn't connected from the beginning?

If I may comment, that's why such changes need to be made by who knows the operation of these circuits.

Capito?

"my little kid"



un abbraccio...

[Waltomatic]

That's pretty confusing me... So why in my interface pin 12 wasn't connected from the beginning?

I think in your case it is not necessary to connect the 12-7, only the others. Perform this test when correcting your switches...

[Alfaeddy]

hello

I have this CAN bus switchover in 2012
as realized

The instructions are in German though, but maybe you can help the

Einbau einer Umschaltung des CAN Bus.pdf

(48.76 KiB) Downloaded 400 times

For xenon is simply a solder to make bridge from pin 7 to 12.

SV300015 CAN Bus.jpg (46.77 KiB) Viewed 4992 times

Finish looked the interface like this


Greeting Eddy

[Racing Man]

I don't think... because when switch 7 is off, nothing is connected... I've made this connection to imitate adapter 1 for my alfa!

BUUUT you amended that wires together at some point, right?

Yes, but AFTER the switch! So when the switch 7 is OFF, it's like nothing is connected together.

[Racing Man]

That's pretty confusing me... So why in my interface pin 12 wasn't connected from the beginning?

But it is just that: the interface reads the STANDARD and the pin 12 is not STANDARD (it's optional), so we do the "transcription" through the Adapter Cable.

The adapter cable, joint wire 7 from the circuit with pin 12 on the obd. On my interface there's NOT a wire 12 from the circuit that goes on pin 12!!

[Racing Man]

That's pretty confusing me... So why in my interface pin 12 wasn't connected from the beginning?

I think in your case it is not necessary to connect the 12-7, only the others. Perform this test when correcting your switches...

But in the adapter3 the wire 7 is connected on pin 12!! Otherwise pin 12 remain disconnected!!

[Waltomatic]

BUUUT you amended that wires together at some point, right?

Yes, but AFTER the switch! So when the switch 7 is OFF, it's like nothing is connected together.

Be the connector side or the card side, if these wires are joined you need a circuit detour when they should be separated, right? If you want use only ONE switch to it is physically impossible.

But in the adapter3 the wire 7 is connected on pin 12!! Otherwise pin 12 remain disconnected!!

The adapter cable, joint wire 7 from the circuit with pin 12 on the obd. On my interface there's NOT a wire 12 from the circuit that goes on pin 12!!

This is one more proof that your connection is wrong (you did not think of it before). I advise you to turn it off and redo following my diagram, forgetting the Adapter Cable 1 for now. MAYBE pin 12 not necessary to read the CAN network of 500, check. If it really is not necessary, you can even use a smaller dip switch (4 way). Anyway, AFTER this connection works, we can think of an alternative. But the same right would buy a Adapter Cable 1, that NOT NEED wire connected to pin 12 in the interface.

[Waltomatic]