FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

[leeg123007]

DSC_1562.JPG (1.15 MiB) Viewed 6398 times

[leeg123007]

DSC_1559.JPG (1.37 MiB) Viewed 6398 times

[leeg123007]

above are the pics of it please could anyone ring or tell me what I need to do or what to remove thanks lee

[Alfaeddy]

Hello

To be able to read at your Fiat 500, the airbag control unit
You will need the yellow adapter (A3) as the CAN bus must be transferred.

http://www.ebay.de/itm/151518618746?_tr ... EBIDX%3AIT

Greeting Eddy

[leeg123007]

hello eddy yeah i am using the yellow adapter but its not allowing me to connect to the airbag or dash modules

[cxem]

The photos no CAN.

[Alfaeddy]

Hello Leek

Think it out closely, you can connect to MotorECU and ABS without adapter manufacture
But with the yellow adapter you get created a connection !!!
So I guess the first one error in the adapter plug !!

question:
Can you handle the yellow adapter to connect other controllers ??

Do you have the registered version of Multiecuscan?


Greeting Eddy

[IRBabuin]

I bought an ELM Bluetooth interface and I can't seem to get it to work. I get the CONNECTION TIMEOUT message when I try to connect to engine ECU. If I test the interface with MES I get the following response:

COMMAND: ATZ
RESPONSE:

ELM327 v2.1

>

COMMAND: ATI
RESPONSE: ATI
ELM327 v2.1

>

COMMAND: ATE0
RESPONSE: ATE0
OK

>

COMMAND: ATL0
RESPONSE: OK

>

COMMAND: ATH0
RESPONSE: OK

>

COMMAND: ATSPC
RESPONSE: OK

>

COMMAND: ATS0
RESPONSE: OK

>

COMMAND: ATCAF0
RESPONSE: OK

>

COMMAND: ATCFC0
RESPONSE: ?

>

COMMAND: ATCRA 7B0
RESPONSE: ?

>

COMMAND: ATSH 7B0
RESPONSE: ?

>

COMMAND: ATAT1
RESPONSE: OK

>

COMMAND: ATST41
RESPONSE: OK

>

COMMAND: ATBI
RESPONSE: OK

>

WARNING: This interface is not compatible with ELM 327 1.3! Will not connect to any CAN module.

During engine interogation, the yellow led on the interface blinks. I activated High latency mode. I selected the correct IO Port from Device Manager. I read here that I need to install the ftdi drivers. I don't understand why, I don't even know if I have a ftdi chip inside.

Please some help.

[durkonorbi]

Hello,

I would like to ask your help; I bought a "little blue" bluetooth ELM327 mini interface; I tried to connect to my FIAT STILO 1.6 (2002, 5 doors) and the next happened:

- connected the ELM to car - ok
- connect with laptop to ELM via BT (MES) - ok
- try to connect to ECU: !PROBLEM! Indicated a lot of fault code, dashboard got black and computer said: LOOSE CONNECTION... after this nothing happened, I could not close the doors with the remote and I have car securiry failure etc... everything goes wriong... After this only the ECU reset helped... (accu contact remove)... It happened again when I tried (and the ame with Torque with my phone). The ELM327 is this:

46794849_1_644x461_elm327-bluetooth-mini.jpg (24.82 KiB) Viewed 6302 times

46794849_1_644x461_elm327-bluetooth-mini_2.jpg (25.37 KiB) Viewed 6302 times

Do you have any idea: is the resistor removing can help?

Thanks,
Norbert

[Waltomatic]

Strange, very strange...