Service Reset on Panda 4x4 1.3 Mjt 75cv DPF

[gioz]

Hi,

I had a problem with Service Reset on Fiat Panda 4x4 (M.Y.2010) 1.3 multijet 75cv 4x4 DPF (Marelli 8DF).
The Automatic Service Reset was well but when I try to set the value "distance of next oil change" manually, its fail.
All other value were changed correctly, only problem is the distance of next oil change

I attached the log.

FESLog_1301101916_Fiat Panda '03 1.3 JTDMultijet.txt

Service Reset LOG

(1.26 KiB) Downloaded 25 times

In addiction, this model of Panda which isn't present in the vehicle list and I have scanned the ecu with Panda 03 JTD/Multijet --> Marelli 8DF CF5/EOBD Diesel Injiection (1.3) but give "Invalid ISO Code". This causes the fail of Adjustments : "Oil change (only DPF version)" and the relatives oil parameters (example % Degrade oil) dont'change.

I attached another log.

FESLog_1301101905_Fiat Panda '03 1.3 JTDMultijet.txt

Oil Change LOG

(793 Bytes) Downloaded 18 times

Please, give me a solutions?

Thanks a lot!

[alfa156sarajevo]

Regarding your first part of post from above, I did mentioned few months ago to Yani that on Panda it is not possible to do manual adjustment for option "distance of next oil change".
Since I was working on petrol car for me was just fine service coupon.
I hope it will be possible in near future...

[yani]

About the service reset:
Did you try to change "Service interval" (Lettura intervallo servizi) and "Service period" to lower values? I added these 2 adjustments since Multiecuscan 1.1 to fix the problem with vehicles where the other two adjustments do not work. You may need to execute "NEXT SERVICE KM RESET" and/or turn the key OFF and then back ON after setting the new values.

About the engine oil change:
This is the correct ECU for your engine. It shouldn't give you Invalid ISO message. There was a bug with some ISO codes in previous versions. Do you use the latest version of Multiecuscan?
Also, what is the value of "Oil change counter"?

[gioz]

About the service reset:
Did you try to change "Service interval" (Lettura intervallo servizi) and "Service period" to lower values? I added these 2 adjustments since Multiecuscan 1.1 to fix the problem with vehicles where the other two adjustments do not work. You may need to execute "NEXT SERVICE KM RESET" and/or turn the key OFF and then back ON after setting the new values.

Ops, I don't have tryed to change "Service Interval" but "distance of next service"! I have resolved whit "service interval", excuse me, works well!

I don't changed the value "Service Period" because this value not appear in the Instrument Cluster, only value showed is remaining km to next service (Service Interval).

About the engine oil change:
This is the correct ECU for your engine. It shouldn't give you Invalid ISO message. There was a bug with some ISO codes in previous versions. Do you use the latest version of Multiecuscan?
Also, what is the value of "Oil change counter"?

I used Multiecuscan 1.1.
Today I installed the last version and Invalid ISO message as disappeared.
I execute again the Adjustments "Oil change (only DPF version)" and "Oil Change Couter" rose from 1.9% to 100%.
Works well!

Regarding your first part of post from above, I did mentioned few months ago to Yani that on Panda it is not possible to do manual adjustment for option "distance of next oil change".
Since I was working on petrol car for me was just fine service coupon.
I hope it will be possible in near future...

Hi, you tryed "Service Interval" Adjustments? On my Panda works perfectly! The distance next oil change is changed!

Thanks a lot for soonest reply and assistance!

Best Regards!