Page 1 of 1
147 1.6 Failed proxy after make windows anti-trap sensors.
Posted: 31 Mar 2011, 08:22
by bubu321
- I has error B1005/ B1006, not active windows anti-trap sensors.
- after doing windows anti-trap sensors procedure ( give complete signal ) must make proxy allignment.
- but procedure proxy alignment failed.
Code: Select all
Engine
Bosch Motronic Me7.3.1 EOBD injection (1 lambda)
ISO Code: 7C 86 8A 80 61
Body
Marelli Body Computer
ISO Code: 40 83 89 80 A1
Dashboard
Service Interval Reset
ISO Code: 32 83 26 85 B5
Driver's Door (TRW)
ISO Code: 86 07 02 19 FD
Boot (TRW)
ISO Code: 07 07 02 19 FE
COMPLETED
- test inside of FES.
Code: Select all
COMMAND: ATZ RESPONSE: ELM327 v1.4
COMMAND: ATI RESPONSE: ATI ELM327 v1.4
COMMAND: ATE0 RESPONSE: ATE0 OK
COMMAND: ATL0 RESPONSE: OK
COMMAND: ATH0 RESPONSE: OK
COMMAND: ATSPC RESPONSE: OK
COMMAND: ATS0 RESPONSE: OK
COMMAND: ATCAF0 RESPONSE: OK
COMMAND: ATCFC0 RESPONSE: OK
COMMAND: ATCRA 7B0 RESPONSE: OK
COMMAND: ATSH 7B0 RESPONSE: OK
COMMAND: ATAT1 RESPONSE: OK
COMMAND: ATST41 RESPONSE: OK
COMMAND: ATBI RESPONSE: OK
This interface is compatible with ELM 327 1.4! Should connect properly with all CAN modules.
- try other interface ELM327 v.1.4, no good result.
- error log
- WARNING: This vehicle is properly configured. PROXI Alignment is not needed!
EXECUTING ADJUSTMENT...
Windows' Anti-Trap Sensors
COMPLETED
EXECUTING ADJUSTMENT...
PROXI Alignment Procedure
Writing CAN configuration data ...
Writing to module: Body Computer Node (NBC)SUCCESS!
0
0
Writing to module: Dashboard Node (NQS)FAILED!
Writing to module: Driver Door Node (NPG)SUCCESS!
Writing to module: Boot Node (NVB)SUCCESS!
Writing to module: Climate Control Node (NCL)SUCCESS!
FAILED TO EXECUTE
- next problem, after exchange dashboard VDO no communication to this instruments.
- but proxy alignment not working.
- Engine
Bosch Motronic Me7.3.1 EOBD injection (1 lambda)
ISO Code: 7C 86 8A 80 61
Body
Marelli Body Computer
ISO Code: 40 83 89 80 A1
Other
Driver's Door (TRW)
ISO Code: 86 07 02 19 FD
Other
Boot (TRW)
ISO Code: 07 07 02 19 FE
COMPLETED
Re: 147 1.6 Failed proxy after make windows anti-trap sensor
Posted: 31 Mar 2011, 14:24
by yani
The PROXI function in 147 fails to configure the instrument cluster node.
This, however, is not a problem in your case as your instrument cluster does not need to be configured.
Please note that the automatic windows function will not work when anti-trap sensors don't work (or when you don't have anti-trap sensors at all).
Re: 147 1.6 Failed proxy after make windows anti-trap sensor
Posted: 01 Apr 2011, 08:31
by bubu321
Code: Select all
after exchange dashboard VDO no communication to this instruments by CAN.
- this is problem because VDO realise this
Code: Select all
VDO ( MannesMan instrumental panel ) VDO Extra:
- inspection service value
- next service reset
- Light setting corr.
- odometr km entry
- dashboard replacement
Re: 147 1.6 Failed proxy after make windows anti-trap sensor
Posted: 01 Apr 2011, 13:38
by alfa156sarajevo
Hi
bubu321
I have almost the same problems as you regarding anti-trap sensors.
I turned on the function and tested a little bit…
Windows were working but only sometimes.
Sometimes they stuck in the middle, sometimes they would work just fine and for a while... And then they stoped...
I guess that I do not have those sensors installed.
I got the same errors like you…
So I turned off the function and delete the errors and everything is back to normal!
Re: 147 1.6 Failed proxy after make windows anti-trap sensor
Posted: 01 Apr 2011, 14:34
by bubu321
@alfa156sarajevo
- and proxy alignment is working without error ?
( hm, AR 147 JTD )
- where is connector for this sensors.
- i will try connect 300 om, but don't know where is connectors.
p.s.
- must be between 1k2 - 1k9 and working.
-
http://img585.imageshack.us/i/czujnikpoprawny.jpg/
Re: 147 1.6 Failed proxy after make windows anti-trap sensor
Posted: 08 Apr 2011, 15:36
by The-Kevster
bubu321 wrote:- and now it 's working.
- add emulator to anti-trap sensor socket.
--
Congratulations! Nice work.
Could you tell me what you did to emulate the anti-trap sensor and where I would find the socket? Currently both of my sensor voltages report 5v so I'm guess this isn't reporting correctly?
Thanks for your help!
Re: 147 1.6 Failed proxy after make windows anti-trap sensor
Posted: 11 Apr 2011, 11:26
by alfa156sarajevo
bubu321 wrote:@alfa156sarajevo
- and proxy alignment is working without error ?
( hm, AR 147 JTD )
- where is connector for this sensors.
- i will try connect 300 om, but don't know where is connectors.
p.s.
- must be between 1k2 - 1k9 and working.
-
http://img585.imageshack.us/i/czujnikpoprawny.jpg/
NO!
The PROXI is not working in all "Nodes".
As you already know that PROXI functions always fails at the "Dash Node" (dashboard).
So I just click execute the PROXI function and that is it!
I have no idea where are these sensors and connectors are. Maybe they should be in doors!?!
As soon as I get some time I will remove door panels and will try to find it...
Re: 147 1.6 Failed proxy after make windows anti-trap sensor
Posted: 11 Apr 2011, 12:20
by The-Kevster
alfa156sarajevo wrote:bubu321 wrote:@alfa156sarajevo
I have no idea where are these sensors and connectors are. Maybe they should be in doors!?!
As soon as I get some time I will remove door panels and will try to find it...
No need to look in the doors. See here
viewtopic.php?f=4&t=1548&start=30#p5899
