No ECU on fiat 500 1.3 Mjet problem not fixed

gargamella · Post by **gargamella** » 28 Nov 2010, 15:09

Hello, i've downloaded new release 2.6.
The test mode in settings (F9) it's ok, but when i select fiat 500, i report error connecting and if i search for ecu (F11), no ecu found.
Another think, my Fiat 500 is mjet and not jtd , is an error of typing or 2.6 don't support fiat 500 1.3 mjt?
Many thanks
Lorenzo

Post by **yani** » 28 Nov 2010, 16:12

Hi,

Please send me a report by clicking at the red "Send Reeport" button which appears after you disconnect (or fail to connect) from the ECU.

Yani

gargamella · Post by **gargamella** » 28 Nov 2010, 17:12

I've sent to you, but it says in anounimous form, check you've received.
But for fiat 500 jtd you mean mtj? is an error of word?
Many thanks
Lorenzo

Post by **yani** » 28 Nov 2010, 18:51

Sorry, but I will need one more report to research into this issue.
I need you to do the following:
1. Scan your vehicle
2. Try to connect to engine or power steering.
3. Send report

Thanks.

gargamella · Post by **gargamella** » 30 Nov 2010, 09:12

Hi Yani, i've re-sent you the report, tell me if is arrived.
The message that i receive from the software is Ecu connection failed, and something about wrong pin.
Could you please answer me about if the fiat 500mjet is named fiat 500 jtd in your software?
I'm talking about the "new fiat 500" year 2008
many thanks Yani

Post by **yani** » 04 Dec 2010, 17:08

Please try version 2.6.1. It should fix this problem.

gargamella · Post by **gargamella** » 05 Dec 2010, 20:46

Hello Yani, i've tryed to connect.
In "engine management" (the first, when i connect, it enter in the ecu, i see immediately the message of "restrition for unregistered version" and immediately remind me back to the first screen when i open the multiecuscan software, and i can't do anything in this parameters. But unregistered version can do something in "engine"?
In "body" and "service" when i try to connect, i obtain the same errors of before, error to connect ecu and wrong pin.
I've sented you 2 report
Many thanks
Lorenzo

Frank · Post by **Frank** » 08 Dec 2010, 16:02

Hello
I too have the same problem.
Using bluetooth ELM327 the test works fine giving it all ok but when I do Connect does not connect and even research ECU.
Fiat 5001.3Mjet 2008

Pardon my English but I'm using a translator

Frank · Post by **Frank** » 12 Dec 2010, 23:48

Nl software is also possible to reset the service more than an oil change?

No ECU on fiat 500 1.3 Mjet problem not fixed

No ECU on fiat 500 1.3 Mjet problem not fixed

Re: No ECU on fiat 500 1.3 Mjet

Re: No ECU on fiat 500 1.3 Mjet

Re: No ECU on fiat 500 1.3 Mjet

Re: No ECU on fiat 500 1.3 Mjet

Re: No ECU on fiat 500 1.3 Mjet

Re: No ECU on fiat 500 1.3 Mjet problem not fixed

Re: No ECU on fiat 500 1.3 Mjet

Re: No ECU on fiat 500 1.3 Mjet