Wrong state of SGW Giulia

[DrVTH]

Hello,

in log file we can see that SGW is removed in node status, but still MES properly discovers existing SGW

Reading CAN configuration data ...
CAN CONFIGURATION DATA:
4F 0C 40 65 10 40 19 02 0A 08 00 00 80 40 01 00 4F 0C 40 65 10 40 19 02 0A 08 00 00 80 40 00 00 04 00 00 00 00 40 00 00 02 08 00 00 00 40 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
4F 0C 40 65 10 40 19 02 0A 08 00 00 80 40 01 00 4B 0C 00 65 10 40 19 02 0A 00 00 00 80 40 00 00 4F 0C 40 65 10 40 19 02 0A 08 00 00 80 40 00 00 4B 0C 00 65 10 40 19 02 0A 00 00 00 80 40 00 00 4B 0C 00 65 10 40 19 02 0A 00 00 00 80 40 00 00
30 34 36 32 30 30 30 32 35 35 31 4F 55 54 50 55 54 2D 53 49 54 20 18 09 05 4F 0C 40 65 10 40 19 02 0A 08 00 00 80 40 01 00 4B 0C 00 65 10 40 19 02 0A 00 00 00 80 40 00 00 43 5D 2F 01 A9 82 07 F3 54 31 A1 07 79 10 10 0A AB 1E 04 72 00 35 73 14 01 4F 03 34 19 83 AC 48 07 43 07 00 80 00 0C 4E 00 00 19 04 00 09 02 5B FA 9D 06 E5 05 31 20 01 71 15 3D 81 10 01 00 DA 00 B7 10 11 00 3D 49 03 03 12 F9 57 A0 00 00 01 00 00 F0 20 08 20 89 0A 00 00 00 00 00 0C 1C 00 00 00 00 31 00 00 00 03 00 02 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Body Computer Node (BCM/NBC)
Engine Control Node (ECM/NCM)
Dashboard Node (IPC/NQS)
Automatic Transmission Node (TCM/NCA/NCR)
Gearbox Selector Node (ESM/GSM/NSC)
Driver Assistant System Node (DASM)
Radio Frequency Hub Node (RFHM)
Drive Train Control Node (DTCM)
Security Gateway Module (SGW)
Climate Control Node (HVAC/NCL)
Entertainment Telematic Node (ETM)
Amplifier Node (AMP)
Comfort Seat and Wheel Node (CSWM)
Left Blind Spot Sensor Node (LBSS)
Right Blind Spot Sensor Node (RBSS)
Entertainment multimedia control module (EMCM)
Engine sound enhacement module (ESEM/ANC)
Electric Steering Node (EPS/NGE)
Brake System Node (ABS/BSM/NFR)
Parking Sensor Node (PAM/NSP)
Airbag Node (NAB/ORC)
Self-adaptive Headlamps Node (AFLS/NFA)
Haptical Lane Feedback Node (HALF)
(Multiecuscan 4.3)
30.12.2018 14:18:00
Alfa Romeo Giulia 2.0 Turbo 16V MultiAir
CAN Setup / PROXI Alignment Procedure (952)
--------------------------------------------------------------

Body Computer Node (BCM/NBC): EOL Ok
Engine Control Node (ECM/NCM): EOL Ok
Dashboard Node (IPC/NQS): EOL Ok
Automatic Transmission Node (TCM/NCA/NCR): EOL Ok
Gearbox Selector Node (ESM/GSM/NSC): Ok
Driver Assistant System Node (DASM): EOL Ok
Radio Frequency Hub Node (RFHM): EOL Ok
Drive Train Control Node (DTCM): EOL Ok
Security Gateway Module (SGW): Removed
Climate Control Node (HVAC/NCL): EOL Ok
Entertainment Telematic Node (ETM): EOL Ok
Amplifier Node (AMP): EOL Ok
Comfort Seat and Wheel Node (CSWM): EOL Ok
Left Blind Spot Sensor Node (LBSS): EOL Ok
Right Blind Spot Sensor Node (RBSS): EOL Ok
Entertainment multimedia control module (EMCM): EOL Ok
Engine sound enhacement module (ESEM/ANC): EOL Ok
Electric Steering Node (EPS/NGE): Ok
Brake System Node (ABS/BSM/NFR): EOL Ok
Parking Sensor Node (PAM/NSP): EOL Ok
Airbag Node (NAB/ORC): EOL Ok
Self-adaptive Headlamps Node (AFLS/NFA): EOL Ok
Haptical Lane Feedback Node (HALF): EOL Ok

WARNING: SGW MODULE DETECTED! Active diagnostics will not be possible on this vehicle!

[StokeR]

How did you remove, deactivate the SGW?

[StokeR]

I have the same problem on my Stelvio 2.0 TB MA.
SGW is also shown as removed allthough its there.

[StokeR]

Bug seems to be fixed.
THX.

[BestROC]

I have the same problem on my Stelvio.

As you can see in the pictures below I have SGW removed and Multiecuscan 4.5 is tell me that I can't do anything do to SGW present.

https://www.it2go.ro/image/catalog/page1.jpg

https://www.it2go.ro/image/catalog/page2.jpg

Do you know if this is only a bug in Multiecuscan or it is somehow still on?