DPF regeneration failed

Report any bugs found in Multiecuscan and suggest new functionality to be implemented
Jerry 159
Posts: 43
Joined: 30 Dec 2009, 10:02
Location: The Netherlands

DPF regeneration failed

Post by Jerry 159 »

Hello Yani,

Yesterdag I had a clogged DPF on my 159 2.4 JTDm 200HP.
I tryed to regenerate with the 1.6 software version, unfortunately it didn`t work :( got this message: "execution failed"

Engine was idling at 800 rpm and warmed up to 90c, also no brake or clutch pedals touched.

Every other function (actuators, reset, values) of your great software is working ok, so its not the cable I think.

Am I doing something wrong, or is it a software glitch?

Please advice,

Jerry
Crombel
Posts: 16
Joined: 23 Dec 2009, 21:58

Re: DPF regeneration failed

Post by Crombel »

The same over here.
My dpf is clogged 92%, I thought all conditions were met but I got the same message.
Does it have to be 100% clogged?
Or is it necessary that the warning light is on?

Croma 1.9 JTD 8V
yani
Site Admin
Posts: 1173
Joined: 06 Nov 2009, 16:40

Re: DPF regeneration failed

Post by yani »

Hi,

Seems that it is a software problem. I will try to resolve it in next release.

Yani
Jerry 159
Posts: 43
Joined: 30 Dec 2009, 10:02
Location: The Netherlands

Re: DPF regeneration failed

Post by Jerry 159 »

Thank you for your effort!
Jerry 159
Posts: 43
Joined: 30 Dec 2009, 10:02
Location: The Netherlands

Re: DPF regeneration failed

Post by Jerry 159 »

Yani, I have tryed the DPF regeneration function for Alfa 159 2.4 JTDm in the latest multiecuscan 2.0:

-Using the ELM327 cable it works perfectly !!!
-With the KKL interface DPF regen is still NOT working. Cable works OK with al functions/reading except DPF regen.

I don`t mind because I have both cables, but maybe its an issue for version 2.1 :)

The local (st)(d)ealer charged me €120,- for DPF regen, so i`m very happy that I can do it with your fantastic software!
yani
Site Admin
Posts: 1173
Joined: 06 Nov 2009, 16:40

Re: DPF regeneration failed

Post by yani »

Thanks for the feedback. It is very helpful.

Yani
the_devil_withe
Posts: 7
Joined: 11 Apr 2010, 00:53

Re: DPF regeneration failed

Post by the_devil_withe »

hello dpf regen work with elm 327?

because the command for that is canbus.
the_devil_withe
Posts: 7
Joined: 11 Apr 2010, 00:53

Re: DPF regeneration failed

Post by the_devil_withe »

Crombel wrote:The same over here.
My dpf is clogged 92%, I thought all conditions were met but I got the same message.
Does it have to be 100% clogged?
Or is it necessary that the warning light is on?

Croma 1.9 JTD 8V

no at all. with 50% and 60% you can regen dpf.
no light on.
dluisao
Posts: 10
Joined: 29 Mar 2010, 21:19

Re: DPF regeneration failed

Post by dluisao »

this tool never regen your dpf.

you need pro device for that.

this device is no correct and all value is no correct when compare with KTS bosch.
Jerry 159
Posts: 43
Joined: 30 Dec 2009, 10:02
Location: The Netherlands

Re: DPF regeneration failed

Post by Jerry 159 »

dluisaorege wrote:this tool never n your dpf.

you need pro device for that.

this device is no correct and all value is no correct when compare with KTS bosch.

Did you try it yourself with ELM327 interface?
NO you did`t !!! because it works! :roll:

After regenerate command in multiecuscan:
- RPM goes from idle 800 rpm in steps to 3500 rpm
- sound from engine is changing (lower note) happens also when its generating during driving.
- after 1 minute a lot of smoke from exhaust (= burned soot)

After regenerate % clogged DPF reading is low.

So with ELM327 & Multiecuscan you can regenerate :mrgreen:
Post Reply