FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

[Alfaeddy]

Hello Paulik

no Grüß Gott, I'm not a Bavarian

In both images, Dortmund and your I can not see anything.

Does not matter.

Power times with MES test and adjust the screen here.

Greeting Eddy

[fefe128]

hi, please what resistance should be removed to let me go all the controllers on FIAT STILO 1.9JTD multivagon 2007 and Alfa romeo giulietta 2.0 JTD 2011 ? Figure in Annex
Thank you very much

ELM 327 1.5a

ELM327.jpg (1.42 MiB) Viewed 6564 times

[Alfaeddy]

Hello

Remove the red marked Resistor


Greetings Eddy

file markiert.jpg (596.28 KiB) Viewed 6561 times

[fefe128]

Hello, thank you it's better to get almost all controllers. But I can not get on Airbag, Electric Power, ABS FIAT Stilo 1.9JTD Multivagon 2007. Can also start these controllers?
the Alfa Romeo Giulietta 2.0JTD 2011 I do not

[vince59]

Finally I found the proper adapter to access all modules and I was able to reset service and oil filter warning linght.
I only have the problem the MULTISCAN does not show the date and reading for service even if the reset works and light disappears.
I had problme resetting the warning light with MES 3.6 and I had to go back to MES 3.3
Can anybody help and give suggestions?

Thank you

[fefe128]

Adapter and what is it? on what kind of car?

[ade739]

Hi Vince 59, which adapter did you use? I have a 1.6 bravo mjt and can only access the service light reset but not the oil service reset using the red elm obd link cable. The alfa 1.6 mjt i did earlier this year, also a 2011 like the Bravo, used the obd red cable plus the yellow A3 interface?

[Alfaeddy]

Hello, thank you it's better to get almost all controllers. But I can not get on Airbag, Electric Power, ABS FIAT Stilo 1.9JTD Multivagon 2007. Can also start these controllers?
the Alfa Romeo Giulietta 2.0JTD 2011 I do not

hello

Of course, do not you come with the Elm to the airbag
For this you need a KKL interface and red adapter (A2)

What is "Power Elektric" I can not translate = MotorECU?

For ABS of course you need the green adapter

On Giulietta only the yellow adapter is needed


I thought this should be understood by the list "Supported Vehicles"

Greeting Eddy

[Alfaeddy]

Finally I found the proper adapter to access all modules and I was able to reset service and oil filter warning linght.
I only have the problem the MULTISCAN does not show the date and reading for service even if the reset works and light disappears.
I had problme resetting the warning light with MES 3.6 and I had to go back to MES 3.3
Can anybody help and give suggestions?

Thank you

Hello

Which car?
Control?

I've also had problems with oil change reset at a Giuletta.
When Marelli ECU you have to enter the date in the English way,
mm.dd.jjjj

And at the Bosch Motronic in German position
dd.mm.jjjj

Different as shown in the MES.

Greeting Eddy

[fefe128]

Hello,
I ELM327 bluetooth as I modify it so that I can diagnose all the control units?
FIAT Stilo 1.9JTD multivagon 2007 and Alfa Romeo Giulietta 2.0JTD 2011