FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Multiecuscan usage help and guides
EddyDj
Posts: 9
Joined: 20 Oct 2014, 17:19

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by EddyDj »

Hi Eddy,
unfortunately I can not unsolder the board, but the photos I sent you do see it in all angles.
The only resistors under the board are: R5 (473 ohms), R6 (103), R7 (103), R16 (102), R17 (102).
It could be r5?
Alfaeddy
Posts: 1350
Joined: 19 Feb 2011, 17:43
Location: Germany , Aarbergen

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by Alfaeddy »

Hi Eddy

Too bad, maybe I can take some pictures of the users from the other forum.
let's see

R5 can not be
If a bridge resistor is present, the imprinted 121 or 1200

But I can think of another
measure times with a multimeter between pin 6 and pin 14 the Ohm value

So you can test whether a bridge resistor is present.

Greetings Eddy
EddyDj
Posts: 9
Joined: 20 Oct 2014, 17:19

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by EddyDj »

Hi,
I measured between pin 6 and pin 14 , and indeed the value is 120 ohms. so there is resistor . now we have to find the bastard resistor :x
Greetings
Alfaeddy
Posts: 1350
Joined: 19 Feb 2011, 17:43
Location: Germany , Aarbergen

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by Alfaeddy »

Hi Eddy


Comparisons times the interface in the image with your
in this I marked the bridge resistor.

What imprint has the resistance in your
ELM Interface ??

Greetings Eddy
IMG_20141003_233836 markiert.jpg
IMG_20141003_233836 markiert.jpg (128.39 KiB) Viewed 5451 times

Edit:

Look on page 144 there is the same board as in your interface

Greetings Eddy
EddyDj
Posts: 9
Joined: 20 Oct 2014, 17:19

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by EddyDj »

Hello Eddy,

unfortunately there is not that resistor in my interface :cry:
EddyDj
Posts: 9
Joined: 20 Oct 2014, 17:19

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by EddyDj »

Hi,
I have found that there are resistors under the tab at the bottom ( as I indicated in the figure) , where they attack the 16-pin ! how can I get them ? come off the 16 pin from the plastic ?
Greetings
IMAG1822.jpg
IMAG1822.jpg (736.29 KiB) Viewed 5446 times
IMAG1823.jpg
IMAG1823.jpg (664.66 KiB) Viewed 5446 times
EddyDj
Posts: 9
Joined: 20 Oct 2014, 17:19

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by EddyDj »

I solved it! The resistor was under, and not to unsolder everything I removed the plastic under the pin to access it and I removed the resistor. Now everything works perfectly! Eddy Thanks for the advice.
Greetings.
IMAG1825.jpg
IMAG1825.jpg (806.07 KiB) Viewed 5436 times
zafron
Posts: 18
Joined: 31 Jul 2014, 19:52

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by zafron »

Hello Alfaeddy

Can you help me with this interface, please? Which resistor should I remove? Thank you.
Attachments
20141025024700218.jpg
20141025024700218.jpg (654.13 KiB) Viewed 5406 times
20141025024908630.jpg
20141025024908630.jpg (716.96 KiB) Viewed 5406 times
Alfaeddy
Posts: 1350
Joined: 19 Feb 2011, 17:43
Location: Germany , Aarbergen

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by Alfaeddy »

hello

Remove the white (8 times) plug housing
And make a picture of it

Which vehicle ???


Greetings Eddy
zafron
Posts: 18
Joined: 31 Jul 2014, 19:52

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by zafron »

My car is Fiat Punto mk2 1.2 16v 2000.
Attachments
IMG_20141026_225613.jpg
IMG_20141026_225613.jpg (562.96 KiB) Viewed 5376 times
Post Reply