Multiecuscan 1.8 RELEASED!

[yani]

Hi,

I released Multiecuscan 1.8 today with the following changes:

- Translation of the yellow description messages in Polish (thanks to @tzok)
- Support for Bosch EDC17CP49 CF5/EOBD Diesel Injection (2.0) (Ducato 250 Facelift)
- Support for Siemens VDO Injection (1.8 16V) (Croma, 159)
- Fixed UniAir actuator dispersion correction procedure on Marelli IAW 8GMF/8GSF
- Added new parameters for Bosch Motronic ME 2.1 (all variants - 2.0, 2.5, 3.0)
- Added new parameters for Bosch Motronic ME 3.1 (all variants - 2.0, 2.4, 3.0)
- Added new parameters for Bosch Motronic ME7.3H4 (Brava, Palio, Punto '99/'03, Y)
- Added new parameters for Bosch Motronic Me7.3.1 EOBD
- Added new parameters for Bosch EDC15 Diesel Injection '99 (1.9JTD) (Punto '99)
- Added new parameters for EDC15 Diesel Injection (1.9JTD, 2.4JTD) (Brava, Marea, Multipla, 145, 146, 156, 166, Kappa, Lybra)
- Added new parameters and procedures for Bosch EDC16C39 CF4/EOBD Diesel Injection (1.9, 2.4)
- Added new parameters and procedures for Bosch EDC16C39 CF5/EOBD Diesel Injection (1.6, 1.9, 2.0)
- Added new procedures for Marelli 6F3 EOBD Diesel Injection (1.3)
- Added new parameters and procedures for Marelli 8DF CF5/EOBD Diesel Injection (1.3)
- Added new parameters and procedures for Bosch EDC16C39 CF4/EOBD Diesel Injection (2.3, 3.0)
- Added new parameters and procedures for Marelli 8DF CF5/EOBD Diesel Injection (1.3)
- Added new parameters and procedures for Marelli 8F3 CF5/EOBD Diesel Injection (1.3 and 2.3)
- Support for DTC Details of Bosch Motronic ME 3.1 EOBD (2.0, 2.4, 3.0V6)
- Support for DTC Details of Bosch EDC15 Diesel Injection '99 (1.9JTD) (Punto '99)
- Support for DTC Details of Bosch EDC15 Diesel Injection (1.9JTD, 2.4JTD) (Brava, Marea, Multipla, 145, 146, 156, 166, Kappa, Lybra)
- Support for DTC Details of Bosch EDC16 CF3/EOBD Diesel Injection (1.9, 2.4) (Stilo, 147, 156'02, 166, GT, Thesis)

There are not many new modules in this release, but we revised a large number of old modules and added new parameters, procedures and error codes to them.

[kobra]

Big thanks to Yani.
A big thank also for Tzoka from Bielsko

[echappatte]

Tried 1.8, unable to connect to any module Punto 2012 1.4 8V

Uninstalled, re-installed 1.7, same problem.

Interface test ok, LEDs blink on ELM, but it is like no car is connected.
Interface bought 6 months ago, worked fine so far.

Any idea ?

EDIT : Found this in log :
Reading CAN configuration data ...
0
Unreliable communication detected!
1

Sent report too.

[renter]

io avevo la licenza attivata e dopo aver installato mi dice che e' versione free!!!
come posso riattivarlo??

[mattydr67]

Send an email to Yani with your HDD ID. He will fix your problem.
The email to send the request is support@multiecuscan.net
Good luck


Merry X-Mas to everyone

[echappatte]

Tried 1.8, unable to connect to any module Punto 2012 1.4 8V

Uninstalled, re-installed 1.7, same problem.

Interface test ok, LEDs blink on ELM, but it is like no car is connected.
Interface bought 6 months ago, worked fine so far.

Any idea ?

EDIT : Found this in log :
Reading CAN configuration data ...
0
Unreliable communication detected!
1

Sent report too.

Just an update :

Received today a new ELM interface, version 1.8 works great with !
My old has died after only some months

Just a bit disappointed for no support/response on this forum, I know MES don't cost me a lot, but some advices can always help.

Regards

[mrcaptainkirk1]

Hi

is anyone else having trouble trying to perform selespeed final calibrations since the update?
before christmas it was working like a dream now i can basically read only. driving me nuts.
i have tried different lap tops i have even tested the interfaces and all is good in that department.
it get's as far as starting on the clutch then spits out errors(r eng error) or (conditions not met)
is dose this on three different vehicles.

i am wondering if its something i am doing wrong or software issue

cheers kirk

[todos]

Yani, a question when you enter the protocols for the new 500 L? thanks

[jony]

Hello Yani ,

about gearbox selespeed Fiat Idea, Linea , ........ CFC-319 ?

some support in next release ?

thanks.

[teris]

Hi,

I released Multiecuscan 1.8 today with the following changes:

- Translation of the yellow description messages in Polish (thanks to @tzok)
- Support for Bosch EDC17CP49 CF5/EOBD Diesel Injection (2.0) (Ducato 250 Facelift)
- Support for Siemens VDO Injection (1.8 16V) (Croma, 159)
- Fixed UniAir actuator dispersion correction procedure on Marelli IAW 8GMF/8GSF
- Added new parameters for Bosch Motronic ME 2.1 (all variants - 2.0, 2.5, 3.0)
- Added new parameters for Bosch Motronic ME 3.1 (all variants - 2.0, 2.4, 3.0)
- Added new parameters for Bosch Motronic ME7.3H4 (Brava, Palio, Punto '99/'03, Y)
- Added new parameters for Bosch Motronic Me7.3.1 EOBD
- Added new parameters for Bosch EDC15 Diesel Injection '99 (1.9JTD) (Punto '99)
- Added new parameters for EDC15 Diesel Injection (1.9JTD, 2.4JTD) (Brava, Marea, Multipla, 145, 146, 156, 166, Kappa, Lybra)
- Added new parameters and procedures for Bosch EDC16C39 CF4/EOBD Diesel Injection (1.9, 2.4)
- Added new parameters and procedures for Bosch EDC16C39 CF5/EOBD Diesel Injection (1.6, 1.9, 2.0)
- Added new procedures for Marelli 6F3 EOBD Diesel Injection (1.3)
- Added new parameters and procedures for Marelli 8DF CF5/EOBD Diesel Injection (1.3)
- Added new parameters and procedures for Bosch EDC16C39 CF4/EOBD Diesel Injection (2.3, 3.0)
- Added new parameters and procedures for Marelli 8DF CF5/EOBD Diesel Injection (1.3)
- Added new parameters and procedures for Marelli 8F3 CF5/EOBD Diesel Injection (1.3 and 2.3)
- Support for DTC Details of Bosch Motronic ME 3.1 EOBD (2.0, 2.4, 3.0V6)
- Support for DTC Details of Bosch EDC15 Diesel Injection '99 (1.9JTD) (Punto '99)
- Support for DTC Details of Bosch EDC15 Diesel Injection (1.9JTD, 2.4JTD) (Brava, Marea, Multipla, 145, 146, 156, 166, Kappa, Lybra)
- Support for DTC Details of Bosch EDC16 CF3/EOBD Diesel Injection (1.9, 2.4) (Stilo, 147, 156'02, 166, GT, Thesis)

There are not many new modules in this release, but we revised a large number of old modules and added new parameters, procedures and error codes to them.

Maybe you must thinking to add in your versions, the way to programming keys!!!
It is very IMPORTAND!!!
REGARDS!!