VAG KKL cable connections

[Alfaeddy]

Hello Monax

Whoud you buy a ELM

This ELM have not an Bridge Resistor
The Seller has remove the Bridge Resistor
of my Infomation

ELM Interface usb
http://www.ebay.de/itm/160996649487?_tr ... EBIDX%3AIT

And a Adapter A3

http://www.ebay.de/itm/151015670657?_tr ... EBIDX%3AIT

Send him a greeting from me ( Eddy)


Greetngs Eddy

[Gatter]

Hahaha Check this out! My new chineese VAGKKL cable..
Airbag is soldered to pin4-5, instead of pin3!
ESP is soldered to pin11-12, instead of pin12-13.
After the modification it works properly.. So first of all you should check the cable for correct pinout.

VAG-409-KKL-USB-FIAT-ECU-scan.jpg (83.03 KiB) Viewed 22221 times

Cable1.jpg (153.5 KiB) Viewed 22221 times

Cable2.jpg (169.58 KiB) Viewed 22221 times

[alfa156sarajevo]

Eddy Thanks for answer. My order is failed. Minus 16$ for me(( Now i know that i need only ELM

On some Grande Punto models you can connect with KKL to service as I can remember but MES disconnects after some seconds...

[alfa156sarajevo]

Hahaha Check this out! My new chineese VAGKKL cable..
Airbag is soldered to pin4-5, instead of pin3!
ESP is soldered to pin11-12, instead of pin12-13.
After the modification it works properly.. So first of all you should check the cable for correct pinout.

Here is pinout for MES:
pin 1 - ABS
pin 3 - Airbag
pin 7 - Engine/Gearbox
pin 9 - EPS
pin 12 - XENON

On all OBD2 interfaces no matter for which group are they made (Vw, Audi, Ford...) pins 4 and 5 are always connected (soldered) together and on pin 16 is always plus (+) from battery.

[Gatter]

Yes you're right, XENON is on the 12 pin.
But my main problem was the Airbag line. Which was soldered to pin 4-5, instead of pin 3! (Red cable)

[D3LTA_NL]

Hahaha Check this out! My new chineese VAGKKL cable..
Airbag is soldered to pin4-5, instead of pin3!
ESP is soldered to pin11-12, instead of pin12-13.
After the modification it works properly.. So first of all you should check the cable for correct pinout.

VAG-409-KKL-USB-FIAT-ECU-scan.jpg

Cable1.jpg

Cable2.jpg

I have same cable

Can you send me picture of youre modifications?

[hungtan]

Hahaha Check this out! My new chineese VAGKKL cable..
Airbag is soldered to pin4-5, instead of pin3!
ESP is soldered to pin11-12, instead of pin12-13.
After the modification it works properly.. So first of all you should check the cable for correct pinout.

VAG-409-KKL-USB-FIAT-ECU-scan.jpg

Cable1.jpg

Cable2.jpg

I have same cable

Can you send me picture of youre modifications?

I have too. Can you say me, How do I connect my car. Skoda octavia 2.0tdi 103 kw 2004.

[Alfaeddy]

Hello hungtah

What software do you want to read your Scoda?
Because Multiecuscan can not connect to your vehicle.

That which is described here has nothing to do with your connection problem.

Greetings Eddy

[hungtan]

Hello Alfaeddy!!
I tried with VAG-409 and VCDS-Lite-1.2 .v.v. All inactive.

[Alfaeddy]

Hello hungtan

As I've written
This is about Multiecuscan and not on VCDS

Why can not connect to the Skoda I do not know.

Greetings Edd