FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

[xarik]

Hello;
Do you know where is R04 on this model?





Thx

[Alfaeddy]

Hello Xarik

First!
- What problem you have?
- Which vehicle / control / year can not you read?
- Is it a CAN bus error?

then
- Your picture is very dark
- I can not see any components in detail

Greetings Eddy

[xarik]

Hello Alfaeddy

- I can read and erased defect but impossible to have access to the service reset for the draining

- for fiat stilo

New picture

http://imageshack.us/photo/my-images/32/r0.JPG/

[Alfaeddy]

Hello Xarik

By the camera flash can be seen only poorly
But your interface does not interfere with the bridge resistor Multiecuscan

You can surely make a connection to the Body Comp?
And also with the CAN setup you can connect?
Right?

Greetings Eddy

[marinozacc]

Hello Alfaeddy
I would buy a OBD for my punto, I don't know which one to take
urgent because I encoding the key!! please

[Alfaeddy]

Hello

What Punto you?
What Year?


For the models from year 99
can the remote control via CAN bus are programmed.

http://www.ebay.de/itm/260754573911?_tr ... EBIDX%3AIT

Or do you want to program the immobilizer?

This is only possible with AlfaOBD

Greetings Eddy

[alfa156sarajevo]

@ xarik & @ Alfaeddy
As I can see on xarix photo is ELM 327 version 1.2 - at least that is written on the board.
As far as I know in that version is not possible to access CAN network.
Version v1.3 and higher can work with CAN network...

Alfaeddy correct me if I am wrong...

[marinozacc]

Hello

What Punto you?
What Year?


For the models from year 99
can the remote control via CAN bus are programmed.

http://www.ebay.de/itm/260754573911?_tr ... EBIDX%3AIT

Or do you want to program the immobilizer?

This is only possible with AlfaOBD

Greetings Eddy

yes i want to encoding the trasponder
it's possible with multi ecuscan too?
thanks for the link , but i'm confused .. autodia327 is the same elm327?
and it will work on ford fiesta (2006) and alfa romeo 147 (2000)??
thank you a lot!!

edit: for example this
http://www.ebay.it/itm/V1-5-ELM327-OBD- ... 48a&_uhb=1

read the same protocol of autodia327.. change anything?

[xarik]

@ xarik & @ Alfaeddy
As I can see on xarix photo is ELM 327 version 1.2 - at least that is written on the board.
As far as I know in that version is not possible to access CAN network.
Version v1.3 and higher can work with CAN network...

Alfaeddy correct me if I am wrong...

I have the yellow, green and red cables.

[Alfaeddy]

@ xarik & @ Alfaeddy
As I can see on xarix photo is ELM 327 version 1.2 - at least that is written on the board.
As far as I know in that version is not possible to access CAN network.
Version v1.3 and higher can work with CAN network...

Alfaeddy correct me if I am wrong...

Hello alfa156sarajevo

You're right of course
I had forgotten that.


Thanks for the correction

I have not seen for so long v1.2 interface more, I had forgotten that.

The v1.2 can not read CAN bus protocol

Greetings Eddy