FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
I have ELM327 with MultiECUScan Software and 2004 Fiat Stilo 1.6.
I can not connect to Body Computer or Proxy module.
I can connect to only engine module.
How is repair this ELM327 ?
Please check it pictures.
Thanks a lot.
I can not connect to Body Computer or Proxy module.
I can connect to only engine module.
How is repair this ELM327 ?
Please check it pictures.
Thanks a lot.
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Hello
Unfortunately, the pictures are very poor can not be seen as extending the tracks and no number on the components to detect
I once marked a resistor of the CAN bus connection could be a problem.
Which number is in the red resistor (121)??
This, it could be
Unfortunately, I can not recognize the course of the tracks.
So I can not be sure
Greetings Eddy
Unfortunately, the pictures are very poor can not be seen as extending the tracks and no number on the components to detect
I once marked a resistor of the CAN bus connection could be a problem.
Which number is in the red resistor (121)??
This, it could be
Unfortunately, I can not recognize the course of the tracks.
So I can not be sure
Greetings Eddy
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Yes this is number 121.
Remove?
Remove?
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Hello
And the resistance of the bridge pin 6 +7 from the MCP chip is soldered?
Then remove it
Unfortunately, the pictures are not very good, and I can not track lanes
Greetings Eddy
And the resistance of the bridge pin 6 +7 from the MCP chip is soldered?
Then remove it
Unfortunately, the pictures are not very good, and I can not track lanes
Greetings Eddy
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
No, i think only pin 6.Alfaeddy wrote:Hello
And the resistance of the bridge pin 6 +7 from the MCP chip is soldered?
Then remove it
Unfortunately, the pictures are not very good, and I can not track lanes
Greetings Eddy
Please check it: http://postimage.org/image/4ztgc76k7/
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Hello
And where is the pin 7 of the MCP chip?
A higher resolution image would be helpful
I've already increased your image
Or try with removing this resistor
But the cautious can even re soldering
Greetings Eddy
And where is the pin 7 of the MCP chip?
A higher resolution image would be helpful
I've already increased your image
Or try with removing this resistor
But the cautious can even re soldering
Greetings Eddy
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Great! You are best engeneer! Thanks a lot.Alfaeddy wrote:Hello
And where is the pin 7 of the MCP chip?
A higher resolution image would be helpful
I've already increased your image
Or try with removing this resistor
But the cautious can even re soldering
Greetings Eddy
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
bluetooth wrote:Great! You are best engeneer! Thanks a lot.Alfaeddy wrote:Hello
And where is the pin 7 of the MCP chip?
A higher resolution image would be helpful
I've already increased your image
Or try with removing this resistor
But the cautious can even re soldering
Greetings Eddy
Hello
Therefore, it has been the correct resistor?
I am glad that I could help you
Good luck with your interface
Greetings Eddy
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
dear Eddy,
bothering you again sorry Engineer, using this interface in pic 1 i only can acess the engine, how i can modify the interface to acess ecu and power steering?
bothering you again sorry Engineer, using this interface in pic 1 i only can acess the engine, how i can modify the interface to acess ecu and power steering?
- Attachments
-
- 3.JPG (1.61 MiB) Viewed 5187 times
-
- 2.JPG (336.67 KiB) Viewed 5187 times
-
- PIC1.jpg (8.98 KiB) Viewed 5225 times
Last edited by stapy on 09 Mar 2013, 19:06, edited 1 time in total.
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Hello Stapy
to 1
Of course you can use this interface with Multiecuscan! Read the posts in this thread of Bluetooth
to 2
With Multiecuscan you can not immobilizer programming
That's what you need but also possibly not, if you use the transponder from the keys of the donor vehicle
Greetings Eddy
to 1
Of course you can use this interface with Multiecuscan! Read the posts in this thread of Bluetooth
to 2
With Multiecuscan you can not immobilizer programming
That's what you need but also possibly not, if you use the transponder from the keys of the donor vehicle
Greetings Eddy