FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

[Alfaeddy]

Hello

First of all, what Windows system you have on your computer?
32 bit or 64 bit?

And besides, both of the same driver 02:08:24

Try this driver

Greetings Eddy

[Luckjs93]

You mean this?

www.ftdichip.com / Drivers / CDM / CDM% 202.08.24% 20WHQL% 20Certified.zip

But once saved and opened, there is no inside. Exe file that will install

HELPPPPPP

[stilo1.6]

Hi I did everything you have said. Removed two resistance R04 and 2 capacitors soldered and still do not know what a proxy alignment procedure could be the problem? Help me please

[Alfaeddy]

Hello Stilo

Again from the beginning!

I have said to you but that you have to remove the resistor R04!
Only the R04 no other

And I have not written anything of the additional resistors and capacitors!
That are not needed!

This FTDI driver is required if your interface is not recognized!

If your interface detected???
Please look in the Control Panel!

You should not listen to 2 members, it only confuses
Either one or the other!

Greetings Eddy

[stilo1.6]

Hello Stilo

Again from the beginning!

I have said to you but that you have to remove the resistor R04!
Only the R04 no other

And I have not written anything of the additional resistors and capacitors!
That are not needed!

This FTDI driver is required if your interface is not recognized!

If your interface detected???
Please look in the Control Panel!

You should not listen to 2 members, it only confuses
Either one or the other!

Greetings Eddy

szia mi ez a FTDI meghajtó. sajnos ezt nem értem. Azt még meg próbálnám. köszönöm

[stilo1.6]

Hello Stilo

Again from the beginning!

I have said to you but that you have to remove the resistor R04!
Only the R04 no other

And I have not written anything of the additional resistors and capacitors!
That are not needed!

This FTDI driver is required if your interface is not recognized!

If your interface detected???
Please look in the Control Panel!

You should not listen to 2 members, it only confuses
Either one or the other!

Greetings Eddy

hey what's with the FTDI driver. Unfortunately, I do not understand. I have yet to try. thank you

[Alfaeddy]

Hello Stilo

Have you installed the FTDI drivers?

FTDI Treiber.jpg (182.81 KiB) Viewed 7187 times

If your interface detected without error?

Systemsteuerung.jpg (41.46 KiB) Viewed 7187 times

Have you asked the Latency Time in 1?

Latency Time.jpg (143.01 KiB) Viewed 7187 times

Otherwise must be some other error

Greetings Eddy

[stilo1.6]

Képkivágás.PNG (95.17 KiB) Viewed 7187 times

Képkivágás.PNG (95.17 KiB) Viewed 7187 times

Hello Stilo

Have you installed the FTDI drivers?

The attachment FTDI Treiber.jpg is no longer available

If your interface detected without error?

The attachment Systemsteuerung.jpg is no longer available

Have you asked the Latency Time in 1?

The attachment Latency Time.jpg is no longer available

Otherwise must be some other error

Greetings Eddy

Hi thank you very much for your help and the pictures but I still can not connect to CANBUS. Only motor. Error codes can be deleted. capacitors and resistors R04 and removed. FDTI installed and configured.

[bricca]

You mean this?

www.ftdichip.com / Drivers / CDM / CDM% 202.08.24% 20WHQL% 20Certified.zip

But once saved and opened, there is no inside. Exe file that will install

HELPPPPPP

Hi, how to install this drivers? There is not an exe. Thank you very much.

[Alfaeddy]

Hello Stilo

Of course, your problem is the CAN bus that everything you've removed and soldered it only relates to the CAN protocol.

Your engine control is read with ISO14230

Presumably you've destroyed your interface with your renovation

Once more:
Only the resistance R04 is removed!

Greetings Eddy