Page 1 of 2
(NIT/NCV) FAILED! - Timeout error
Posted: 18 Oct 2022, 13:50
by misc0
Hi,
I'm trying to perfom a proxi aligment on my Fiat Bravo 1.6 Easy Multijet. (Not sure if need to choose Fiat 07 or 2014)
Everything works fine except this error: Writing to module: Info-Telematic/Convergence Node (NIT/NCV) FAILED! - Timeout error
I removed the blue&me computer because of battery draining so after remove this ODO start blinking all time. Trying to perfom a proxi aligment to remove the ODO blink.
Any idea about why I'm having this error: Writing to module: Info-Telematic/Convergence Node (NIT/NCV) FAILED! - Timeout error???
Thank you.
Re: (NIT/NCV) FAILED! - Timeout error
Posted: 22 Oct 2022, 10:16
by chrener
As you said Blue&me is removed... This is Convergence Node...
What did you do with proxi? Just alignment or did you try some settings?
Send your configuration and we will see more...
Re: (NIT/NCV) FAILED! - Timeout error
Posted: 23 Oct 2022, 22:17
by misc0
chrener wrote: ↑22 Oct 2022, 10:16
As you said Blue&me is removed... This is Convergence Node...
What did you do with proxi? Just alignment or did you try some settings?
Send your configuration and we will see more...
Thanks for your reply.
I followed this tutorial: https://www.youtube.com/watch?v=RD__7upfeaw
Replaced values:
Steering wheel buttons: "Type B, 8 Buttons" to "Type A, 6 buttons, no CTM"
Auxiliary audio input: "Enabled" to "Not enabled"
Audio output: "Stereo audio/CAN tel.mute" to "Mono audio/analog tel.mute"
Blue&me was draining the battery so I removed it. Tried to run the proxi aligment with Blue&me pluged in but I get the same error.
LOG:
Code: Select all
Reading CAN configuration data ...
CAN CONFIGURATION DATA:
05 00 84 4F 05 00 84 4F 01 00 04 03 00 00 00 01 00 00 00 00
05 00 84 4F 04 00 04 89 05 00 84 4F 04 00 04 89 04 00 04 09
30 34 31 39 38 30 31 34 36 32 30 4F 55 54 50 55 54 2D 4A 49 54 20 14 05 06 4F 84 00 05 89 04 00 04 C1 01 00 07 8F 50 16 00 00 02 84 06 01 28 00 2E C0 81 00 73 00 54 00 00 00 00 00 00 00 00 36 41 05 0C 01 00 00 00 3A 10 28 00 00
Body Computer Node (BCM/NBC)
Engine Control Node (ECM/NCM)
Electric Steering Node (EPS/NGE)
Dashboard Node (IPC/NQS)
Brake System Node (ABS/BSM/NFR)
Info-Telematic/Convergence Node (NIT/NCV)
Climate Control Node (HVAC/NCL)
Side Acceleration / Yaw Node (NYL)
Parking Sensor Node (PAM/NSP)
Airbag Node (NAB/ORC)
18/10/2022 16:26:55
Fiat Bravo 2014 1.6 Multijet 16V
CAN Setup / PROXI Alignment Procedure
--------------------------------------------------------------
Body Computer Node (BCM/NBC): EOL Ok
Engine Control Node (ECM/NCM): Ok
Electric Steering Node (EPS/NGE): Ok
Dashboard Node (IPC/NQS): EOL Ok
Brake System Node (ABS/BSM/NFR): Ok
Info-Telematic/Convergence Node (NIT/NCV): -
Climate Control Node (HVAC/NCL): EOL Ok
Side Acceleration / Yaw Node (NYL): Ok
Parking Sensor Node (PAM/NSP): Ok
Airbag Node (NAB/ORC): EOL Ok
EXECUTING ADJUSTMENT...
PROXI ALIGNMENT PROCEDURE
Writing CAN configuration data ...
Writing to module: Body Computer Node (BCM/NBC) SUCCESS!
Writing to module: Dashboard Node (IPC/NQS) SUCCESS!
Writing to module: Info-Telematic/Convergence Node (NIT/NCV) FAILED! - Timeout error
Writing to module: Climate Control Node (HVAC/NCL) SUCCESS!
Writing to module: Airbag Node (NAB/ORC) SUCCESS!
FAILED TO EXECUTE
Info-Telematic/Convergence Node (NIT/NCV) FAILED! - Timeout error
Re: (NIT/NCV) FAILED! - Timeout error
Posted: 24 Oct 2022, 08:42
by shpuncik
disconnect B&M module and do proxi alignment then. choose Bravo '07
Re: (NIT/NCV) FAILED! - Timeout error
Posted: 26 Oct 2022, 08:29
by misc0
shpuncik wrote: ↑24 Oct 2022, 08:42
disconnect B&M module and do proxi alignment then. choose Bravo '07
B&M module is disconnected. I get the same error even when is connected, looks like B&M computer is broken.
Is there any way to disable/disconnect B&M module from MES before run the proxi alignment??
Re: (NIT/NCV) FAILED! - Timeout error
Posted: 31 Oct 2022, 19:36
by chrener
Hi!
Try this config:
30 34 31 39 38 30 31 34 36 32 30 4F 55 54 50 55 54 2D 4A 49 54 20 14 05 06 4F 84 00 05 09 04 00 04 C1 01 00 07 8F 50 16 00 00 02 84 06 01 28 00 2E C0 81 00 73 00 54 00 00 00 00 00 00 00 00 36 41 05 0C 01 00 00 00 3A 10 28 00 00
Re: (NIT/NCV) FAILED! - Timeout error
Posted: 05 Nov 2022, 17:56
by misc0
chrener wrote: ↑31 Oct 2022, 19:36
Hi!
Try this config:
30 34 31 39 38 30 31 34 36 32 30 4F 55 54 50 55 54 2D 4A 49 54 20 14 05 06 4F 84 00 05 09 04 00 04 C1 01 00 07 8F 50 16 00 00 02 84 06 01 28 00 2E C0 81 00 73 00 54 00 00 00 00 00 00 00 00 36 41 05 0C 01 00 00 00 3A 10 28 00 00
How can I change this?
Re: (NIT/NCV) FAILED! - Timeout error
Posted: 07 Nov 2022, 08:48
by chrener
Hi!
Run MES / Body / Proxi / Adjustments
Press Alt+Ctrl+C and save your current setting in to file!
Copy my setting and paste it to tab...
Run proxialignment procedure...
Re: (NIT/NCV) FAILED! - Timeout error
Posted: 08 Nov 2022, 20:36
by misc0
chrener wrote: ↑07 Nov 2022, 08:48
Hi!
Run MES / Body / Proxi / Adjustments
Press Alt+Ctrl+C and save your current setting in to file!
Copy my setting and paste it to tab...
Run proxialignment procedure...
Done, but I'm still getting same error
Executed as Fiat Bravo 2014 1.6 Multijet 16V:
Code: Select all
Reading CAN configuration data ...
CAN CONFIGURATION DATA:
05 00 84 4F 05 00 84 4F 00 00 00 03 00 00 00 01 00 00 00 00
05 00 84 4F 04 00 04 89 05 00 84 4F 04 00 04 89 04 00 04 09
30 34 31 39 38 30 31 34 36 32 30 4F 55 54 50 55 54 2D 4A 49 54 20 14 05 06 4F 84 00 05 89 04 00 04 C1 01 00 07 8F 50 16 00 00 02 84 06 01 28 01 2E C0 81 00 73 00 54 00 00 00 00 00 00 00 00 36 41 05 0C 01 00 00 00 3A 10 28 00 00
Body Computer Node (BCM/NBC)
Engine Control Node (ECM/NCM)
Electric Steering Node (EPS/NGE)
Dashboard Node (IPC/NQS)
Brake System Node (ABS/BSM/NFR)
Info-Telematic/Convergence Node (NIT/NCV)
Climate Control Node (HVAC/NCL)
Side Acceleration / Yaw Node (NYL)
Parking Sensor Node (PAM/NSP)
Airbag Node (NAB/ORC)
08/11/2022 15:17:51
Fiat Bravo 2014 1.6 Multijet 16V
CAN Setup / PROXI Alignment Procedure
--------------------------------------------------------------
Body Computer Node (BCM/NBC): EOL Ok
Engine Control Node (ECM/NCM): Ok
Electric Steering Node (EPS/NGE): Ok
Dashboard Node (IPC/NQS): EOL Ok
Brake System Node (ABS/BSM/NFR): Ok
Info-Telematic/Convergence Node (NIT/NCV): -
Climate Control Node (HVAC/NCL): EOL Ok
Side Acceleration / Yaw Node (NYL): Ok
Parking Sensor Node (PAM/NSP): Ok
Airbag Node (NAB/ORC): EOL Ok
CUSTOM PROXI NEW DATA:
30 34 31 39 38 30 31 34 36 32 30 4F 55 54 50 55 54 2D 4A 49 54 20 14 05 06 4F 84 00 05 09 04 00 04 C1 01 00 07 8F 50 16 00 00 02 84 06 01 28 00 2E C0 81 00 73 00 54 00 00 00 00 00 00 00 00 36 41 05 0C 01 00 00 00 3A 10 28 00 00
EXECUTING ADJUSTMENT...
PROXI ALIGNMENT PROCEDURE
Writing CAN configuration data ...
Writing to module: Body Computer Node (BCM/NBC) SUCCESS!
Writing to module: Dashboard Node (IPC/NQS) SUCCESS!
Writing to module: Info-Telematic/Convergence Node (NIT/NCV) FAILED! - Timeout error
Writing to module: Climate Control Node (HVAC/NCL) SUCCESS!
Writing to module: Airbag Node (NAB/ORC) SUCCESS!
FAILED TO EXECUTE
Info-Telematic/Convergence Node (NIT/NCV) FAILED! - Timeout error
Executed as Fiat Bravo '07 1.6 Multijet 16V:
Code: Select all
Reading CAN configuration data ...
CAN CONFIGURATION DATA:
05 00 84 4F 05 00 84 4F 00 00 00 03 00 00 00 01 00 00 00 00
05 00 84 4F 04 00 04 09 05 00 84 4F 04 00 04 89 04 00 04 09
30 34 31 39 38 30 31 34 36 32 30 4F 55 54 50 55 54 2D 4A 49 54 20 14 05 06 4F 84 00 05 09 04 00 04 C1 01 00 07 8F 50 16 00 00 02 84 06 01 28 00 2E C0 81 00 73 00 54 00 00 00 00 00 00 00 00 36 41 05 0C 01 00 00 00 3A 10 28 00 00
Body Computer Node (BCM/NBC)
Engine Control Node (ECM/NCM)
Electric Steering Node (EPS/NGE)
Dashboard Node (IPC/NQS)
Brake System Node (ABS/BSM/NFR)
Info-Telematic/Convergence Node (NIT/NCV)
Climate Control Node (HVAC/NCL)
Side Acceleration / Yaw Node (NYL)
Parking Sensor Node (PAM/NSP)
Airbag Node (NAB/ORC)
08/11/2022 15:20:35
Fiat Bravo '07 1.6 Multijet 16V
CAN Setup / PROXI Alignment Procedure
--------------------------------------------------------------
Body Computer Node (BCM/NBC): EOL Ok
Engine Control Node (ECM/NCM): Ok
Electric Steering Node (EPS/NGE): Ok
Dashboard Node (IPC/NQS): EOL Ok
Brake System Node (ABS/BSM/NFR): Ok
Info-Telematic/Convergence Node (NIT/NCV): -
Climate Control Node (HVAC/NCL): EOL Ok
Side Acceleration / Yaw Node (NYL): Ok
Parking Sensor Node (PAM/NSP): Ok
Airbag Node (NAB/ORC): EOL Ok
CUSTOM PROXI NEW DATA:
30 34 31 39 38 30 31 34 36 32 30 4F 55 54 50 55 54 2D 4A 49 54 20 14 05 06 4F 84 00 05 09 04 00 04 C1 01 00 07 8F 50 16 00 00 02 84 06 01 28 00 2E C0 81 00 73 00 54 00 00 00 00 00 00 00 00 36 41 05 0C 01 00 00 00 3A 10 28 00 00
EXECUTING ADJUSTMENT...
PROXI ALIGNMENT PROCEDURE
Writing CAN configuration data ...
Writing to module: Body Computer Node (BCM/NBC) SUCCESS!
Writing to module: Dashboard Node (IPC/NQS) SUCCESS!
Writing to module: Info-Telematic/Convergence Node (NIT/NCV) FAILED! - Timeout error
Writing to module: Climate Control Node (HVAC/NCL) SUCCESS!
Writing to module: Airbag Node (NAB/ORC) SUCCESS!
FAILED TO EXECUTE
Info-Telematic/Convergence Node (NIT/NCV) FAILED! - Timeout error
Re: (NIT/NCV) FAILED! - Timeout error
Posted: 09 Nov 2022, 20:04
by misc0
Proxi alignment failed, but ODO stop blinking!!!!
Looks like this config worked.
Problem solved, thank you so much!