Multiecuscan

Hi,

I retrofit blue & me module to my Alfa 159.
After this - odometer flashes.
So, using MES 2.2 i made proxi aligment with success.
I can connect to B&M module with no errors reported.

Here is CAN scan and proxi aligment log:

Reading CAN configuration data ...
CAN CONFIGURATION DATA:
05 32 97 FB 05 32 97 FB 00 00 00 40 00 00 00 00 00 00 00 00
05 32 97 FB 00 22 05 89 05 32 97 FB 00 22 05 89 00 22 05 89
32 31 31 34 30 30 30 30 37 32 38 4F 55 54 50 55 54 2D 4A 49 54 20 05 10 13 FB 97 32 05 89 05 22 00 C1 65 20 07 B7 00 34 10 00 06 94 06 01 00 02 06 08 00 00 22 50 65 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 45 40 B1 98 00
Body Computer Node (NBC)
Engine Control Node (NCM)
Dashboard Node (NQS)
Steering Wheel Controls Node (NVO)
Receiver Radio/Radio Navigator Node (NRR/RMN)
Brake System Node (NFR)
Info-Telematic/Convergence Node (NIT/NCV)
Driver Door Node (NPG)
Boot Node (NVB)
Climate Control Node (NCL)
Steering Angle Sensor Node (NAS)
Side Acceler./Yaw Node (NYL)
Passenger Door Node (NPP)
Passive Entry Node (NPE)
Steering Lock Node (NBS)
Parking Sensor Node (NSP)
Airbag Node (NAB)
2016-01-03 15:09:46
CONNECTED TO:
Alfa Romeo 159 1.9 JTDm 16V
CAN Setup / PROXI Alignment Procedure
--------------------------------------------------------------

Body Computer Node (NBC): EOL Ok
Engine Control Node (NCM): Ok
Dashboard Node (NQS): EOL Ok
Steering Wheel Controls Node (NVO): Ok
Receiver Radio/Radio Navigator Node (NRR/RMN): Ok
Brake System Node (NFR): Ok
Info-Telematic/Convergence Node (NIT/NCV): EOL Ok
Driver Door Node (NPG): EOL Ok
Boot Node (NVB): Ok
Climate Control Node (NCL): EOL Ok
Steering Angle Sensor Node (NAS): Ok
Side Acceler./Yaw Node (NYL): Ok
Passenger Door Node (NPP): EOL Ok
Passive Entry Node (NPE): Ok
Steering Lock Node (NBS): EOL Ok
Parking Sensor Node (NSP): Ok
Airbag Node (NAB): Ok

WARNING: This vehicle is properly configured. PROXI Alignment is not needed!
EXECUTING ADJUSTMENT...
Information displayed
Old value: Type 2
New value: Type 1/Blue&Me
COMPLETED


EXECUTING ADJUSTMENT...
PROXI ALIGNMENT PROCEDURE
Writing CAN configuration data ...
Writing to module: Body Computer Node (NBC) SUCCESS!
Writing to module: Dashboard Node (NQS) SUCCESS!
Writing to module: Info-Telematic/Convergence Node (NIT/NCV) SUCCESS!
Writing to module: Driver Door Node (NPG) SUCCESS!
Writing to module: Climate Control Node (NCL) SUCCESS!
Writing to module: Passenger Door Node (NPP) SUCCESS!
Writing to module: Steering Lock Node (NBS) SUCCESS!
COMPLETED

Using phone button on steering wheel i can see: Telephone menu with two elements: last calls and phonebook, and nothing more.
Using src button on steering wheel i can see: SEARCHING CONNECTION and nothing happens.

My mobile phone see myCAR bluetooth module but i cant connect becuse of PIN (i dont know this PIN).

So mayabe i should setup some options before proxi aligment ?
In proxi adjustmensts i have:
Steering Wheel Buttons (1) - Type D/159
Display type - Matrix/4 lines
Audio output -Stereo audio/can tel.mute
Auxilary audio input - type 3/159
Information displayed - Type1/Blue&Me

Can You help me ?
And sory for my english ...