Multiecuscan

Hello, Yani

Thanks for ur knowlage,

My problem was that my stilo 1.2 16V 2002 year did not want to start i bought it us faulty. FES shown no problems but i done some voltage check and spot that ECU engine is faulty. So change it to other one from the same model without ASR, unfortunetly i coudnt start car coz immo. So they send me from the same car body computer and key. and car starts Yuppi. Now i need ur magic. I need to configure body computer to switch on ASR on it. Please help

P.S. I can not connect ot proxi aligment us well eighter on old or new body computer i get message:

Reading CAN configuration data
Unreliable communication detected!
1


This is from old body i think

2011-08-27 14:54:08
CONNECTED TO:
FIAT STILO 1.2 16V
CAN Info


List of configured control units :
Body Computer Node (NBC): Present
Engine Control Node (NCM): Present
Electric Steering Node (NGE): Present
Dashboard Node (NQS): Present
Steering Wheel Controls Node (NVO): Not present
Receiver Radio/Radio Navigator Node (NRR/RMN): Present
Brake System Node (NFR): Present
Info-Telematic/Convergence Node (NIT/NCV): Not present
Driver Door Node (NPG): Present
Boot Node (NVB): Not present
Climate Control Node (NCL): Not present
Automatic Transmission Node (NCA-NCR): Not present
Steering Angle Sensor Node (NAS): Not present
Parking Brake Control Node (NPB): Not present
Ceiling Node (NIM): Not present
Side Acceler./Yaw Node (NYL): Not present
Adaptive Cruise Control Node (NAC): Not present
Passenger Door Node (NPP): Present
Driver Seat Node (NAG): Not present
Assisted Braking Node (NBA): Not present
Passive Entry Node (NPE): Not present
Steering Lock Node (NBS): Not present
Gearbox Selector Node (NSC): Not present
Passenger Seat Node (NAP): Not present
Parking Sensor Node (NSP): Not present
Engine Signals Node (NSM): Not present
Airbag Node (NAB): Not present
Air Suspension Node (NMA): Not present
Roll Control Node (NRC): Not present
Self-adaptive Headlamps Node (NFA): Not present
Haptical Lane Feedback Node (HALF): Not present
:
List of active control units :
Body Computer Node (NBC): Active
Engine Control Node (NCM): Active
Electric Steering Node (NGE): Active
Dashboard Node (NQS): Active
Steering Wheel Controls Node (NVO): Not active
Receiver Radio/Radio Navigator Node (NRR/RMN): Active
Brake System Node (NFR): Active
Info-Telematic/Convergence Node (NIT/NCV): Not active
Driver Door Node (NPG): Active
Boot Node (NVB): Not active
Climate Control Node (NCL): Not active
Automatic Transmission Node (NCA-NCR): Not active
Steering Angle Sensor Node (NAS): Not active
Parking Brake Control Node (NPB): Not active
Ceiling Node (NIM): Not active
Side Acceler./Yaw Node (NYL): Not active
Adaptive Cruise Control Node (NAC): Not active
Passenger Door Node (NPP): Active
Driver Seat Node (NAG): Not active
Assisted Braking Node (NBA): Not active
Passive Entry Node (NPE): Not active
Steering Lock Node (NBS): Not active
Gearbox Selector Node (NSC): Not active
Passenger Seat Node (NAP): Not active
Parking Sensor Node (NSP): Not active
Engine Signals Node (NSM): Not active
Airbag Node (NAB): Not active
Air Suspension Node (NMA): Not active
Roll Control Node (NRC): Not active
Self-adaptive Headlamps Node (NFA): Not active
Haptical Lane Feedback Node (HALF): Not active



This is from new one:

2011-09-23 19:14:09
CONNECTED TO:
FIAT STILO 1.2 16V
CAN Info

List of configured control units :
Body Computer Node (NBC): Present
Engine Control Node (NCM): Present
Electric Steering Node (NGE): Present
Dashboard Node (NQS): Present
Steering Wheel Controls Node (NVO): Not present
Receiver Radio/Radio Navigator Node (NRR/RMN): Present
Brake System Node (NFR): Present
Info-Telematic/Convergence Node (NIT/NCV): Not present
Driver Door Node (NPG): Present
Boot Node (NVB): Not present
Climate Control Node (NCL): Not present
Automatic Transmission Node (NCA-NCR): Not present
Steering Angle Sensor Node (NAS): Not present
Parking Brake Control Node (NPB): Not present
Ceiling Node (NIM): Not present
Side Acceler./Yaw Node (NYL): Not present
Adaptive Cruise Control Node (NAC): Not present
Passenger Door Node (NPP): Present
Driver Seat Node (NAG): Not present
Assisted Braking Node (NBA): Not present
Passive Entry Node (NPE): Not present
Steering Lock Node (NBS): Not present
Gearbox Selector Node (NSC): Not present
Passenger Seat Node (NAP): Not present
Parking Sensor Node (NSP): Not present
Engine Signals Node (NSM): Not present
Airbag Node (NAB): Not present
Air Suspension Node (NMA): Not present
Roll Control Node (NRC): Not present
Self-adaptive Headlamps Node (NFA): Not present
Haptical Lane Feedback Node (HALF): Not present
:
List of active control units :
Body Computer Node (NBC): Active
Engine Control Node (NCM): Active
Electric Steering Node (NGE): Active
Dashboard Node (NQS): Active
Steering Wheel Controls Node (NVO): Not active
Receiver Radio/Radio Navigator Node (NRR/RMN): Active
Brake System Node (NFR): Active
Info-Telematic/Convergence Node (NIT/NCV): Not active
Driver Door Node (NPG): Active
Boot Node (NVB): Not active
Climate Control Node (NCL): Not active
Automatic Transmission Node (NCA-NCR): Not active
Steering Angle Sensor Node (NAS): Not active
Parking Brake Control Node (NPB): Not active
Ceiling Node (NIM): Not active
Side Acceler./Yaw Node (NYL): Not active
Adaptive Cruise Control Node (NAC): Not active
Passenger Door Node (NPP): Active
Driver Seat Node (NAG): Not active
Assisted Braking Node (NBA): Not active
Passive Entry Node (NPE): Not active
Steering Lock Node (NBS): Not active
Gearbox Selector Node (NSC): Not active
Passenger Seat Node (NAP): Not active
Parking Sensor Node (NSP): Not active
Engine Signals Node (NSM): Not active
Airbag Node (NAB): Not active
Air Suspension Node (NMA): Not active
Roll Control Node (NRC): Not active
Self-adaptive Headlamps Node (NFA): Not active
Haptical Lane Feedback Node (HALF): Not active

When i put my old body computer ASR problem disapeer but i can not start car coz of immo.

So, you don't have a log file from the old Body Computer?
That's not very good as we need the original car configuration (from the old Body) to program the new one properly.

However, please send me a report (using the red Send Report button in Multiecuscan) after trying to do PROXI alignment and I will see what I can do about it.
Also, send me a PM with the date/time when you sent the report.

Yani

just send u a report when i tryied to connect to proxi aligment 23-09-2011 at 20 45 uk time. Regarding body i still got an old one tell me what kind of data u need and i will post it to u. i done can info in body section and post it on forum. New one and old one. is that what u need??

Yani solved, i found a lose on green connector to the body. Done proxi and all fine thanks for ur help again.