Page 1 of 1
Problems connecting to ECU
Posted: 21 Sep 2011, 16:38
by amiko
HI!!!
I have bought ELM327 and installed driver for it and Multiecuscan.
I have chosen my car in selection (Alfa Romeo 159 2.2JTS 16V), defined ELM 327 v 1.3+ and correct port (COM6) but multiecuscan can not connect to my car.
Please HELP!!!
Re: Problems connecting to ECU
Posted: 21 Sep 2011, 17:20
by Alfaeddy
Hello
A friend had the same problem, all settings were correct but can not connect.
Only after he has gewachelt the interface in the OBD connector, a connection was made.
There was a contact problem!
Here are a few possible problems.
Your interface is correctly identified in the Control Panel?
You have the latency time is set to 1?
Press the test button once to the right of the interface specification
What does it say?
Greetings Eddy
Re: Problems connecting to ECU
Posted: 21 Sep 2011, 18:11
by amiko
1. yes, control panel OK
2. latency - is set to 1
3. when I push TEST, everything is OK
Re: Problems connecting to ECU
Posted: 22 Sep 2011, 07:25
by amiko
Any ideas?
Please help me.
I need your consultation very much!
Re: Problems connecting to ECU
Posted: 22 Sep 2011, 11:43
by Alfaeddy
Hello
Do not hesitate even a screen test of your ELM Interface
Because there must be able to be an error or you should connect.
Greetings Eddy
Edit:
Hello
I see in your screen just yet, you still have the old 2.6 version of FES with the new 3.2 should not be a difference but a test would not damage.
Loading the new version on some tests and the
Re: Problems connecting to ECU
Posted: 22 Sep 2011, 12:38
by amiko
Alfaeddy wrote:Hello
Do not hesitate even a screen test of your ELM Interface
Because there must be able to be an error or you should connect.
Greetings Eddy
Edit:
Hello
I see in your screen just yet, you still have the old 2.6 version of FES with the new 3.2 should not be a difference but a test would not damage.
Loading the new version on some tests and the
I don't understand what you are saying.
I have wrong version of multiecuscan?
Re: Problems connecting to ECU
Posted: 22 Sep 2011, 18:45
by Alfaeddy
Sorry, I translate with Google
Take a screenshot on the test of the ELM interface.
I want to see what is displayed there.
Your FES is an old version 2.6
have you tried the version 3.2 again?
Greetings Eddy
Re: Problems connecting to ECU
Posted: 22 Sep 2011, 18:52
by amiko
Alfaeddy wrote:Sorry, I translate with Google
Take a screenshot on the test of the ELM interface.
I want to see what is displayed there.
Your FES is an old version 2.6
have you tried the version 3.2 again?
Greetings Eddy
On the TEST of ELM327 is showing OK about everything, absolutely.
I'll make screenshots tomorrow.
Yes, I know it is an old version, but I don't know what is the difference between new version and older one.
Re: Problems connecting to ECU
Posted: 22 Sep 2011, 22:44
by Alfaeddy
It is true, even with the old version should be able to get a connection
But if I have connection problems, I would also test a new version.
But it could be something not be right with the FES version?
Greetings Eddy
Re: Problems connecting to ECU
Posted: 23 Sep 2011, 07:53
by amiko
here you can read the resoults of TEST:
COMMAND: ATZ
RESPONSE: ATZELM327 v1.4>
COMMAND: ATE0
RESPONSE: ATE0OK>
COMMAND: ATL0
RESPONSE: OK>
COMMAND: ATH0
RESPONSE: OK>
COMMAND: ATSPC
RESPONSE: OK>
COMMAND: ATS0
RESPONSE: OK>
COMMAND: ATCAF0
RESPONSE: OK>
COMMAND: ATCFC0
RESPONSE: OK>
COMMAND: ATCRA 7B0
RESPONSE: OK>
COMMAND: ATSH 7B0
RESPONSE: OK>
COMMAND: ATAT1
RESPONSE: OK>
COMMAND: ATST41
RESPONSE: OK>
COMMAND: ATBI
RESPONSE: OK>
COMMAND: ATZ
RESPONSE: ELM327 v1.4>