Multiecuscan

hi.

guys I have a big problem!
yesterday everything worked when I wanted to connect with the driver of the car. Today I changed my laptop to another but weaker performance is ok (1.7 ghz processor and 1.5 GB RAM memory)

I wanted to connect to my Fiat Brava (I've done it many times with success). I connected everything as always.
The only mistake I made haste to me is that the power cord from the ground (-) touched the clamp from the battery positive (+) for a split second, clicked a little bit. Then I plugged everything correctly, the red light in the KKL vag is lit normally.

Only at this point the problems begin with the connection of all engine ECU does not respond, ABS ECU is not responding ....

now anyway. I also tried it ELM327 1.4 to connect to the engine and it's the same messages? my friend gave me his ELM 327 1.3 + and have nothing you can not do.

The question of whether there is something wrong in the laptop (yesterday to connect without a problem). Do burned interface, or 3 pin adapter cable. Why is that I have 4 versions of FES on the same hard disk 2.6, 2.6.1, 2.7, 2.7.1 but in the previous laptop had the same and acted.


I installed the interface on port com1. How to turn scan 2.7 interfaces in the FES is to write that he found on the interface is COM PORT 3?
Strange .... I change positions on the computer com port 3 interface is then again when he writes that there is no interface








interface is, of course, is connected to the same USB port in which it was installed

any ideas ?????? please help

Multiecuscan 2.6 craked .....

Shadeyman wrote:Multiecuscan 2.6 craked .....

Polish language in side

Today uninstalled everything. Interfaces, all versions of the FES. There is nothing in the computer. I downloaded the new FES 2.7.1 but not installed any of the interface. FES turn and immediately see the settings in Polish, it displays the position of my car? (Brava 1.2 16V) remembers it - how? When I go to the tab interface - it would point scan-search interface, there is an inscription: THIS FUNCTION INTERFACES Scan CONNECTED TO YOUR COMPUTER. INTERFACE MUST BE CONNECTED TO THE CAR.

I have no user interface is installed, all usb empty, I'm home and not in the car, turn on the scan and after a while, he writes: I found INTERFACE VAG / COM PORT COM 3

HOW?? I is not got NOTHING INSTALLED??

Don't worry about the "found" interface on COM3. Just ignore it. It does not affect the functionality of the program.
The search function simply finds a loopback serial interface at COM3. This could be a simple loopback serial driver of some other software... or something like this.

The interface must be connected to the car when searching for interfaces because most of the interfaces do not work without power from the OBD port.

Your problem seems very weird. It should not be a problem that you touched your interface to +. Also, if the interface is damaged then why it does not work with other interface.
Did you test on another car? It is possible that you have blown some fuse on your car.

ok guys. KKL vag bought new and it works on another laptop. The only confusion is how I met 2 times disconnects me after about 15 seconds.
Message associated with the delay ????, but everything was set up as before. Then the call lasted just a few minutes reading the parameters while the engine, abs, etc.

Tell time to be set correctly (look pictures):
4096 ? or 1024 ?
speed 9600 for vag kkl & 38400 for elm327
I know the delay time = 1
KWP200 = what to give?

No. 1 is my laptop: DELL D610 1.73 GHz 1.5 GB RAM
No.2 is my laptop: HP 4510 2.2 GHz dual 3 GB RAM

How to install an interface to the installer during the installation stops and asks for the file:
ftser2k.sys
This file is in the drivers folder, but you have to select it manually. earlier this was not i