Page 66 of 255
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 06 Apr 2013, 12:26
by Nelson
Helo,wath resistor must remove from ELM327 v1.4 to work to fiat stilo 1.6 16v from 2003?I removed 2 resistor from picture circel 085831,i don't now but i do not know if i did well.
Thank's.
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 06 Apr 2013, 14:11
by Nelson
More photo with my elm327 v1.4,does anyone know if I did well taking out the two resistant from picture?,does anyone know what resistance must remove so I can use?
Thank's
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 06 Apr 2013, 21:26
by Alfaeddy
Hello Nelson
Your removal of the resistors was wrong!
Why did you do that?
There is nowhere where
This is you at your Stilo not the ECU can read a setting error
No resistance error
The users here in the forum should not be the same for the first difficulties you
Open Interface and remove anything.
This is a fatal error
Your interface have before you removed the highlighted resistors
All controls can be read apart from the airbag
Greetings Eddy
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 07 Apr 2013, 03:19
by Nelson
Ok, if you stick to place the 2 resistors that I took that resistance must get her to work?
Thank's.
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 07 Apr 2013, 11:46
by Alfaeddy
Hello Nelson
Yes, as I have already written !
With your ELM interface you can without changing anything on the board
Read your engine and ancillary equipment
Greetings Eddy
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 07 Apr 2013, 11:55
by Nelson
I understand,i put back 2 resistor,but dont work,wath i must do?
Thank's for suport Eddy
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 07 Apr 2013, 13:47
by Alfaeddy
Nelson wrote:I understand,i put back 2 resistor,but dont work,wath i must do?
Thank's for suport Eddy
Hello Nelson
I can not tell you!
Since I do not know if you know the right
- Drivers have installed?
- The Latency Time've set to 1
- Have made the settings on Multiecuscan / settings correct?
- Using the right adapter?
- Your ELM to the Soldery still works.?
Greetings Eddy
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 08 Apr 2013, 05:32
by Nelson
Thank's Eddy,i hope to tell me somebody how to repair the ELM v1.4,i have Fiatecuscan 3.6.
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 08 Apr 2013, 06:45
by Alfaeddy
Nelson wrote:Thank's Eddy,i hope to tell me somebody how to repair the ELM v1.4,i have Fiatecuscan 3.6.
Hello Nelson
Wiso an old version (Fiatecuscan 3.6?)
is the registered version?
or there is a free version?
About 1.5 years ago I had a user who also had connection problems
At that time, the problem was an illegal version of Fiatecuscan
With these versions, there are often problems
Greetings Eddy
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 08 Apr 2013, 11:45
by Nelson
Hello Eddy,its a registred version 3.6,and when I try to connect appear message: SUITABLE INTERFACE NOT FOUND.
A GOOD DAY.