Multiecuscan

Waltomatic wrote:

Alfaeddy wrote:hello

In this ELM all possible circuits are housed in 2 switch positions, there is no need for adapters.

viewtopic.php?f=5&t=4297&p=15111#p15111

Greeting Eddy

Exactly, but it's not a "dip switch", it's a "change-over switch", as I said...

But this switch replaces all adapters (A1, A3, A4 purple)

This is a multi-switch
not as the simple CAN bus switching


Greeting Eddy

Alfaeddy wrote:

Waltomatic wrote:

Alfaeddy wrote:hello

In this ELM all possible circuits are housed in 2 switch positions, there is no need for adapters.

viewtopic.php?f=5&t=4297&p=15111#p15111

Greeting Eddy

Exactly, but it's not a "dip switch", it's a "change-over switch", as I said...

But this switch replaces all adapters (A1, A3, A4 purple)

This is a multi-switch
not as the simple CAN bus switching


Greeting Eddy

So when activated, connect together pin 7 and pin 12 (making a bridge)? I need just to connect to xenon!

Alfaeddy wrote:But this switch replaces all adapters (A1, A3, A4 purple)

This is a multi-switch
not as the simple CAN bus switching


Greeting Eddy

OK!

Racing, you can include 12-7 in it, respecting the disconnection of 7 when linking with 12.

Waltomatic wrote:Racing, you can include 12-7 in it, respecting the disconnection of 7 when linking with 12.

I've tried that way, but it don't connect with the xeno ecu...
In normal operation, just switching the wire 7 from pin 7 to pin 12, it doesn't connect... So, seeing adapter #1, where 7, 9, 12, 1 are linked toghether, maybe to connect with xenon pin 7 and 12 must be joint together to wire 7?

Racing Man wrote:

Waltomatic wrote:Racing, you can include 12-7 in it, respecting the disconnection of 7 when linking with 12.

I've tried that way, but it don't connect with the xeno ecu...
In normal operation, just switching the wire 7 from pin 7 to pin 12, it doesn't connect... So, seeing adapter #1, where 7, 9, 12, 1 are linked toghether, maybe to connect with xenon pin 7 and 12 must be joint together to wire 7?

No, according Supported Vehicles you need the same A3. You welded wire on pin 12 of connector?

Waltomatic wrote:

Racing Man wrote:

Waltomatic wrote:Racing, you can include 12-7 in it, respecting the disconnection of 7 when linking with 12.

I've tried that way, but it don't connect with the xeno ecu...
In normal operation, just switching the wire 7 from pin 7 to pin 12, it doesn't connect... So, seeing adapter #1, where 7, 9, 12, 1 are linked toghether, maybe to connect with xenon pin 7 and 12 must be joint together to wire 7?

No, according Supported Vehicles you need the same A3. You welded wire on pin 12 of connector?

No, I've only put a switch on wire 7, that connects pin 7 or pin 12. Should I weld pins 7 and 12 together? Why the same A3? In this picture is shown A1

Cáspita!!! Você não disse que era do Alfa, kkkkkkk



Meu conselho: esqueça a adaptação para o Alfa e compre um cabo.

Waltomatic wrote:Cáspita!!! Você não disse que era do Alfa, kkkkkkk
Meu conselho: esqueça a adaptação para o Alfa e compre um cabo.

I've written it few pages before, I forgot to repeat it!

And that's why I've welded some pins together before!!!

I've to try to weld together pin 7 and 12 to wire 7, and see what happens...

Let It Be...

Well, as I said it would be more accurate to buy the adapter 1, but you may even be able to. Each adapter connects a wide variety of vehicles and systems, and perhaps Alfa not need all the wires together. Hopefully, only 12-7. My diagram allows this option.