Page 35 of 255
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 24 Sep 2012, 09:25
by westfielder
Just registered so I can say THANK YOU to all who have contributed to this thread. I removed R04 and can now communicate with all my elm compatible CAN modules.
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 27 Sep 2012, 10:43
by diablotic
Hi,
I can see many different mobos but I cannot find similar to mine. Can anyone please help me and show which resistor should I remove please?
- IMG-20120927-00085.jpg (573.14 KiB) Viewed 7076 times
- IMG-20120927-00084.jpg (685 KiB) Viewed 7076 times
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 27 Sep 2012, 11:42
by Alfaeddy
Hello Diablotic
The error you have with your interface?
Which version is your interface?
With which you can control establish a connection?
This ELM interface does not have this annoying resistor
And should really be able to connect.
Greetings Eddy
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 27 Sep 2012, 11:48
by diablotic
Basically when I do the interface search I can find my ELM but I have "latency too high" message at the bottom. All the tests are OK but I can see this error and I also have difficuties to connect to FIAT cars so that's why I thought I need to do some kind of trick with my interface.
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 27 Sep 2012, 13:52
by Krg
diablotic wrote:... which resistor should I remove please?
I have the same interface that conforms to the circuit Datasheet (
http://elmelectronics.com/DSheets/ELM327DS.pdf)
http://multiecuscan-france.forumgratuit ... elm327-v15
No connection problem.
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 27 Sep 2012, 18:13
by lolo85v
Hello on my elm I is to remove the resistance r4 but always the problem to reach has airbag
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 27 Sep 2012, 18:54
by mattydr67
Do you have Airbag on CAN BUS or k-line?
Or you need to use the 3rd Adaptor for this?
Did you checked the Coverage list to see what you need to acces to your airbag?
By the way did you tried to connect to the BSI or other CAN BUS controlers?
Think about this first then we will see what can be your issue
Good luck
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 27 Sep 2012, 19:41
by Alfaeddy
Hello
How Mattydr67 already writing
I will once again make clear
The problem with the resistor in the ELM interface affects only
The controllers will be read with CAN (ISO 15765)
And no controls with the KWP2000 (ISO14230) or K-Line (KW1281)
Therefore, not just remove a resistor from the board, often it is also because incorrect settings why no connection can be made.
Also concerns this resistor only this software (Multiecuscan) all other software have no problem with this resistance in the ELM
Greetings Eddy
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 28 Sep 2012, 01:10
by lolo85v
Hello in fact I have to buy 3 elm I have to remove the resistance on 3 elm 2 on 3 walk(work) tres indeed on airbag 3 eme elm do not arrive.
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 28 Sep 2012, 07:10
by Alfaeddy
Hello
What kind of vehicle?
Model?
Airbag?
Greetings Eddy