Page 225 of 255
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 01 May 2017, 06:22
by cxem
At you the basic chip "
STM32F032 - a drop"
You need the main chip "
PIC"
====================================
Problem:
COMMAND: ATSPC
The operation has timed out.
0 - Automatic
1 - SAE J1850 PWM (41.6 kbaud)
2 - SAE J1850 VPW (10.4 kbaud)
3 - ISO 9141-2 (5 baud init, 10.4 kbaud)
4 - ISO 14230-4 KWP (5 baud init, 10.4 kbaud)
5 - ISO 14230-4 KWP (fast init, 10.4 kbaud)
6 - ISO 15765-4 CAN (11 bit ID, 500 kbaud)
7 - ISO 15765-4 CAN (29 bit ID, 500 kbaud)
8 - ISO 15765-4 CAN (11 bit ID, 250 kbaud)
9 - ISO 15765-4 CAN (29 bit ID, 250 kbaud)
A - SAE J1939 CAN (29 bit ID, 250* kbaud)
B - USER1 CAN (11* bit ID, 125* kbaud)
C - USER2 CAN (11* bit ID, 50* kbaud)
"STM32F032 - drop" - It is a small set of commands(program: OBD Car Doctor, Torque)
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 02 May 2017, 10:32
by samuraisuzuki
Ok, man. many thanks.... I will buy the interface with PIC chip
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 04 May 2017, 14:13
by samuraisuzuki
Ok, I have it! It works and can read alot of data from Motor Control Unit.
But why cannot I write down the Injectors codes? Program says the Error and Interface is not compatible with the function.
(((
The victory seemed so close (((
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 05 May 2017, 03:27
by cxem
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 17 May 2017, 11:31
by riki77
Hello everybody.
This is my ELM 327 Interface
Could I modify it and how, please.
https://www.amazon.it/gp/product/B00UR5 ... UTF8&psc=1
Thank you so much!
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 19 May 2017, 21:31
by bigwolfys
riki77 wrote:Hello everybody.
This is my ELM 327 Interface
Could I modify it and how, please.
Thank you so much!
The picture quality is not very good. But apparently you need to remove R2
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 20 May 2017, 03:14
by palote
Hi
Fiat uno evo 1.0 2015 not supported?
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 24 May 2017, 16:46
by slickkon
Hi,
I seem to be having trouble connecting to CAN system ln my Fiat Bravo T-Jet 2009. Anyone can advise if my device is something wrong? Possible to modify?
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 26 May 2017, 22:00
by slickkon
slickkon wrote:Hi,
I seem to be having trouble connecting to CAN system ln my Fiat Bravo T-Jet 2009. Anyone can advise if my device is something wrong? Possible to modify?
Hi can a kind soul help please?
I scan interface in settings and multiecuscan find interface, when run test, first tests all ok, but the last 'COMMAND ATSPC: The Operation Has Timed Out'
but cannot connect to any module (engine, service, body, etc).
Many thanks!
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 03 Jun 2017, 11:24
by Rwbjj
Hi,
New to the forum but I'll jump straight in with a query...
I recently bought a cheapish "Pumpkin" branded wifi Elm327 box assuming that I'd probably have to modify it and remove the 120ohm resistor to get it to work correctly.
The error I get in MES is consistent with incorrect CAN termination. However, the PCB doesn't seem to have a 120ohm resistor. In fact, the resistance between can high/low pins appears to be 48.4k rather than the expected 120ohm.
Image of the board:
Any thoughts?
Or do I just buy another. If so, any decent uk amazon sellers with quick delivery?
~Ben