Page 216 of 255
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 11 Jan 2017, 20:12
by Alfaeddy
Hello LukasCA
Even without modification you should be able to connect to the engine control unit with the interface.
The resistor may only cause problems for CAN bus controllers.
And the motor control of the 159 is not read via CAN bus.
Which driver was installed
You have established all the settings
What is the interface test in Multiecuscan?
Greeting Eddy
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 11 Jan 2017, 22:52
by Alex2011fiat
Hi
I have this ELM327 v1.5 Wifi and I can't connect to CAN interfaces (Body). Only engine.
The car is Fiat Stilo.
It's the same problem with a resistor? Which one please?
Thanks a lot!!!
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 11 Jan 2017, 23:20
by Alfaeddy
Hallo
It is the Resistor R1 with the Number 121
´Greeting Eddy
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 12 Jan 2017, 15:55
by obdspecialist
Hi
No resistor to detach or replace
Buy this one and you get into 100% ECUs of FIAT GROUP
http://www.obdspecialist.it/prodotto-14 ... -FREE.aspx
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 12 Jan 2017, 19:13
by Alfaeddy
Hello
@ obdspecalist
This one also
http://www.ebay.de/itm/152303738760?_tr ... EBIDX%3AIT
and to an better price
Greeting Eddy
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 14 Jan 2017, 18:48
by GAlt
Hello guys, i have chinese Elm327 Bluetooth, but some 2016 version
i doubt it can be done to connect with CAN, even to see the board, but although i will post picture of the board if someone know something?
Best Regards
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 14 Jan 2017, 22:03
by Alfaeddy
Hello Galt
Make an Interface Test with Multiecuscan
and post an Screen with an Image
On your Board can´t find an Bridge Resistor
the Motor ecu ist read not with CAN Bus
Also your connect must with no one modifikation
Greetings Eddy
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 15 Jan 2017, 14:34
by GAlt
Alfaeddy wrote:Hello Galt
Make an Interface Test with Multiecuscan
and post an Screen with an Image
On your Board can´t find an Bridge Resistor
the Motor ecu ist read not with CAN Bus
Also your connect must with no one modifikation
Greetings Eddy
COMMAND: ATZ
RESPONSE: ATZ
ELM327 v1.5>
COMMAND: ATI
RESPONSE: ATI
ELM327 v1.5>
COMMAND: ATE0
RESPONSE: ATE0?>
COMMAND: ATL0
RESPONSE: ATL0?>
COMMAND: ATH0
RESPONSE: ATH0?>
COMMAND: ATSPC
RESPONSE: ATSPC?>
COMMAND: ATS0
RESPONSE: ATS0?>
COMMAND: ATCAF0
RESPONSE: ATCAF0?>
COMMAND: ATCFC0
RESPONSE: ATCFC0?>
COMMAND: ATCRA 7B0
RESPONSE: ATCRA 7B0?>
COMMAND: ATSH 7B0
RESPONSE: ATSH 7B0?>
COMMAND: ATAT1
RESPONSE: ATAT1
OK>
COMMAND: ATST41
RESPONSE: ATST41?>
COMMAND: ATBI
RESPONSE: ATBI?>
WARNING: This interface is not compatible with ELM 327 1.3! Will not connect to any CAN module.
This is my test. This warning in the end i have and in my another WiFi Elm, but there is no problem with CAN, but this....
p.s. I know that engine is not on CAN
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 15 Jan 2017, 20:17
by Alfaeddy
Hello Galt
I thought it already this interface is not compatible with MES and also AlfaOBD
There are only a few v1.5 ELM interfaces that work.
This has nothing to do with a bridge resistor.
Greeting Eddy
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 16 Jan 2017, 10:41
by GAlt
Alfaeddy wrote:Hello Galt
I thought it already this interface is not compatible with MES and also AlfaOBD
There are only a few v1.5 ELM interfaces that work.
This has nothing to do with a bridge resistor.
Greeting Eddy
Thanks a lot anyway Eddy. I thought that v1.5 will not be a problem, becouse my WiFi version is also 1.5 and do not have this problem, but anyway...which version of bluetooth is best?