Multiecuscan

Hello everyone,

i have a Fiat Punto 1.3 multijet, i bought elm v1.5a.

When i try to connect to Mes not working.

See the immages at http://imgur.com/a/tmE5S

How resistor should I remove?

Thanks for help

Hello

I suspect R2 is the bridge resistor
but since you can only guess I just a picture of a page have.

It is also helpful if you set a screen of the interface test here.

Greeting Eddy

Thanks Eddie,

this is the interface http://imgur.com/SUHjgft.


I removed the R2 but nothing...

Hello Sardegna

For the reason, a screen of the interface test is so important
as already written several times the interface since 2015 only
rarely with MES Works

Greeting Eddy

Sorry for my English.
Fiat Panda 2008 dialogic (selespeed)
ELM 327 WI-FI USB
wires suitable for pin 2,4-5,6,7,9,14,16
reads transmission - gearbox, removes (delite) the error codes , but does not do service work on the clutch calibration torirovaniyu and other works , removes the error codes , but does not do service work on the clutch calibration torirovaniyu and other works.
How resistor should I remove
Thanks for help
https://drive.google.com/file/d/0BxHjrm ... sp=sharing
https://drive.google.com/file/d/0BxHjrm ... sp=sharing
https://drive.google.com/file/d/0BxHjrm ... sp=sharing
https://drive.google.com/file/d/0BxHjrm ... sp=sharing
https://drive.google.com/file/d/0BxHjrm ... sp=sharing
https://drive.google.com/file/d/0BxHjrm ... sp=sharing
https://drive.google.com/file/d/0BxHjrm ... sp=sharing
https://drive.google.com/file/d/0BxHjrm ... sp=sharing
https://drive.google.com/file/d/0BxHjrm ... sp=sharing
https://drive.google.com/file/d/0BxHjrm ... sp=sharing
https://drive.google.com/file/d/0BxHjrm ... sp=sharing
https://drive.google.com/file/d/0BxHjrm ... sp=sharing

Hi all,

I am hoping you can help me out I am trying to get a elm327 working on JT850 PWM and I am having no luck I am hoping someone here may be able to help me out I am attaching photos of the PCB.





Thanks,
Yonu

Hello. Can somebody help me which resistor I need to destroy to connect my car's dahsboard. I need proxy alignment. Alfa Romeo 147 1,9 JTD

https://photos.google.com/share/AF1QipP ... R3U2NMU093

Thanks for the help

A good link is www.electronic-fuchs.de
Die sprechen deutsch.

I just want to by on e-bay proper interface that I can use for things I explained in my other post on wrong topics. It is for Fiat bravo '08, 1.9 16V. So what to look for on ebay? If you can send me a link, it would be great. I prefer bluetooth, but if there isn't any of it USB is fine too.

So is it something this:
This interface: http://www.ebay.com/itm/Auto-V2-1-Inter ... SwKfVXD8wb

+ this A1 adapter cable:
http://www.ebay.com/itm/Diagnose-Adapte ... OSwDk5ULac~

Whit this I can access to engine, ABS, ESP, airbag modules etc...

Thanks

Have you ever seen this elm327 1.5 PCB ?
USB communication is ok but no connection to OBD (tested on a Fiat Punto 1.3 JTD Blue&ME 2011 and with EasyOBD, with and without adapter 3 (yellow)).
No result with "Scan for Interfaces" feature in Multiecuscan settings.
Where is the resistor to cut ? (R14???)
http://s32.postimg.org/f1k370ok5/20160428_203842.jpg
http://s32.postimg.org/r0vlebu51/20160428_203913.jpg