Page 3 of 5
Re: Multiecuscan 2.0 - WORK IN PROGRESS!!!
Posted: 15 Mar 2010, 19:36
by albertodg2
Hi:
I need the support of the Bosch Motronic ME796 for Palio 1.2 16v
Thanks
Re: Multiecuscan 2.0 - WORK IN PROGRESS!!!
Posted: 15 Mar 2010, 21:07
by Pustynnikov
For anyone asked, but no answer: Can you please tell how much estimated will cost commercial version of the excellent programs Multiecuscan in version 2.0?
Expecting the support of the old ECU, such as Bosch Monojetronic & Etc?
And, if you need some help with translation into Russian language - I'm ready to help.
Thanks
Re: Multiecuscan 2.0 - WORK IN PROGRESS!!!
Posted: 16 Mar 2010, 10:31
by Entonox
yani wrote:"Service Reset" for Fiat Stilo will be available in the new version.
You will need ELM327 v1.3 or newer.
Yani
Is the elmscan5 kabel from scantools.net suitable for this? as it is a cheap cable...
Re: Multiecuscan 2.0 - WORK IN PROGRESS!!!
Posted: 16 Mar 2010, 11:35
by yani
Entonox wrote:Is the elmscan5 kabel from scantools.net suitable for this? as it is a cheap cable...
I'm not 100% sure because I don't have it, but according to the info on internet it has EML 327 v1.3a inside. So, it should work.
Re: Multiecuscan 2.0 - WORK IN PROGRESS!!!
Posted: 16 Mar 2010, 15:16
by Entonox
what kind of cable do you advise to use? (Brand/Type)
Re: Multiecuscan 2.0 - WORK IN PROGRESS!!!
Posted: 16 Mar 2010, 15:59
by fs1958
Hi yani,
can´t await the new version with ELM 327 support. Currently I am using USB version of ELMScanmaster OEM (WG-Soft) with a USB ELMCanII adapter cable. Will that cable be supported as well?
BR,
Frank
Re: Multiecuscan 2.0 - WORK IN PROGRESS!!!
Posted: 17 Mar 2010, 09:33
by alfa156sarajevo
fs1958 wrote:Hi yani,
can´t await the new version with ELM 327 support. Currently I am using USB version of ELMScanmaster OEM (WG-Soft) with a USB ELMCanII adapter cable. Will that cable be supported as well?
BR,
Frank
I think it will be supported! Did you bought you interface on web page
www.obd-2.de?
According to web page
www.obd-2.de your USB ELMcanII adapter cable is ELM 327 1.3a version and
yani in previous message wrote that for multiecuscan version 2.0 will be needed ELM 327 inteface v1.3 or newer.
Re: Multiecuscan 2.0 - WORK IN PROGRESS!!!
Posted: 19 Mar 2010, 14:31
by fs1958
... so it should work! Great!
Re: Multiecuscan 2.0 - WORK IN PROGRESS!!!
Posted: 19 Mar 2010, 18:15
by Hari-Alfa
Hi Yani!
I would like to ask, what's the problem? Today I tried to Alfa156 Selespeed '00, and the engines are not connected!
- The airbag OK!
Then I tried 147 1.6 103LE ('05) and managed everything perfectly!
What could be the problem?
Re: Multiecuscan 2.0 - WORK IN PROGRESS!!!
Posted: 21 Mar 2010, 19:39
by stopino
I try the last version and you software is very interesting.
I need the correction about DPF regeneration.
If it possible in next version 1,6 mjt or t-jet of Alfa Mito
Good job !