Multiecuscan

Hello R1taka

Ja, R04 is the right Resistor


Greetings Eddy

djakon999 wrote:Other side is very difficult to caputre good quallity photo
http://i63.tinypic.com/1z23p5w.jpg
http://i65.tinypic.com/294p8o0.jpg

Hello

While it's not your interface
but the same construction boards




Greeting Eddy


Sorry, I can at the moment not insert images
This appears to me.

"Sorry, the board attachment quota has been reached."

We had the board been here

Alfaeddy wrote:

djakon999 wrote:Other side is very difficult to caputre good quallity photo
http://i63.tinypic.com/1z23p5w.jpg
http://i65.tinypic.com/294p8o0.jpg

Hello

While it's not your interface
but the same construction boards




Greeting Eddy


Sorry, I can at the moment not insert images
This appears to me.

"Sorry, the board attachment quota has been reached."

We had the board been here

Hello, please upload image to other server like imageshack or tinypic. You can also give me page number of this tread where it was.

Alfaeddy wrote:Hello R1taka

Ja, R04 is the right Resistor


Greetings Eddy

Hi Eddy,

Unfortunately, it didn't work. I've remove the R04, but there is no change - I can still connect to the engine only. Any other ideas?

Regards, M1taka

Hello M1taka

To which vehicle is located ????
Such information is also important

Greeting Eddy

HI
i am haveing problem with elm 327 obd bluetooth adapter i got from aliexpress (2 of them). When i connect adapter to car obd (fiat bravo 2012, 1.6 mjtd) dash board instrumets go crazy. Fule and temp guage goes to 0 and i got massage on dash display that parking senzors are unavailable, also something about airbag. Thing is the same when try to connect to Stilo 1.9 JTD. It reads Renault Megane III and Duster with no problems. I tried with removeing bridge rez but it behaves the same. Any suggestion ?

Here are the link to elm and picture of board

http://www.aliexpress.com/item/Super-Mi ... 21578.html

http://www.aliexpress.com/item/2014-Top ... 41617.html


http://postimg.org/image/uepmf25m1/

i removed circuled rezistor

Hello Bozza

It is important that you set a screen of Interface Test here.
There are many interface that no longer work with MES.
The ELM for € 6.85 I also do not run with MES
Information about Megane and Duster are useless because you can not read with MES these vehicles.
And this is about MES (Multiecuscan)

Greeting Eddy

Alfaeddy wrote:Hello M1taka

To which vehicle is located ????
Such information is also important

Greeting Eddy

Eddie,

The car is Alfa Romeo 156 Sportwagon 1.9 jtd, Prod. date: 14/6/2002, the ECU is EDC15C7, like this one: https://ecu.co.uk/alfa-romeo/engine-con ... 02073.html
I hope this info helps.

Regards, M1taka

Hello M1taka
Thanks for the information, the sooner to knowledge would be an advantage was
Because
Needs to read a Alfa 156 with MES the bridge resistance not be removed because the Alfa 156 has no CAN bus.
Your interface should work just as well without modification with MES.
Is your interface at all compatible with MES ??
Which driver you installed ??
Make a test interface with MES and put a screen here.

Those are always the same questions I here first of all has to find out
Greeting Eddy

Alfaeddy wrote:Hello Bozza

It is important that you set a screen of Interface Test here.
There are many interface that no longer work with MES.
The ELM for € 6.85 I also do not run with MES
Information about Megane and Duster are useless because you can not read with MES these vehicles.
And this is about MES (Multiecuscan)

Greeting Eddy

i will post scr from MES, i am just wodering is that cind of behavior with dash board normal, i mention Renault just to say that adapter work with other cars and software