Page 193 of 255
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 09 Nov 2015, 15:24
by djakon999
Hello, I have ELM327 mini bluetooth adapter and can't connect to CAN interfaces on my Fiat Punto 2004. Anyone can help with my adapter?
Inside photo
http://i68.tinypic.com/161dh21.jpg
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 09 Nov 2015, 22:39
by Alfaeddy
Hello deacon
Make nevertheless please times a screen from the test with Multiecuscan
Settings / Interfaces / Test
Because the first thing we need to determine the compatibility with MES.
Greeting Eddy
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 10 Nov 2015, 09:23
by m1taka
Hi all,
Could anyone tell me which resistor should I remove in order to be able to connect to the Climate Control as well (currently I'm connecting to the engine only). Here is the Chinese device I got:
https://drive.google.com/file/d/0B8L9oy ... sp=sharing
https://drive.google.com/open?id=0B8L9o ... HFYTF9ZLVk
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 10 Nov 2015, 17:42
by djakon999
Hello Alfaeddy,
COMMAND: ATZ
RESPONSE: ATZ
ELM327 v1.5
>
COMMAND: ATI
RESPONSE: ATI
ELM327 v1.5
>
COMMAND: ATE0
RESPONSE: ATE0
OK
>
COMMAND: ATL0
RESPONSE: OK
>
COMMAND: ATH0
RESPONSE: OK
>
COMMAND: ATSPC
RESPONSE: OK
>
COMMAND: ATS0
RESPONSE: OK
>
COMMAND: ATCAF0
RESPONSE: OK
>
COMMAND: ATCFC0
RESPONSE: OK
>
COMMAND: ATCRA 7B0
RESPONSE: OK
>
COMMAND: ATSH 7B0
RESPONSE: OK
>
COMMAND: ATAT1
RESPONSE: OK
>
COMMAND: ATST41
RESPONSE: OK
>
COMMAND: ATBI
RESPONSE: OK
>
This interface is compatible with ELM 327 1.4! Should connect properly with all CAN modules.
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 10 Nov 2015, 21:36
by Alfaeddy
Hello M1taka
Remove the white plastic housing at 8 pin connector
including the bridge resistance should be located.
And make a new image, or rummage through this thread in accordance to your board
Greeting Eddy
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 10 Nov 2015, 21:39
by Alfaeddy
djakon999 wrote:Hello Alfaeddy,
COMMAND: ATZ
RESPONSE: ATZ
ELM327 v1.5
>
COMMAND: ATI
RESPONSE: ATI
ELM327 v1.5
>
COMMAND: ATE0
RESPONSE: ATE0
OK
>
COMMAND: ATL0
RESPONSE: OK
>
COMMAND: ATH0
RESPONSE: OK
>
COMMAND: ATSPC
RESPONSE: OK
>
COMMAND: ATS0
RESPONSE: OK
>
COMMAND: ATCAF0
RESPONSE: OK
>
COMMAND: ATCFC0
RESPONSE: OK
>
COMMAND: ATCRA 7B0
RESPONSE: OK
>
COMMAND: ATSH 7B0
RESPONSE: OK
>
COMMAND: ATAT1
RESPONSE: OK
>
COMMAND: ATST41
RESPONSE: OK
>
COMMAND: ATBI
RESPONSE: OK
>
This interface is compatible with ELM 327 1.4! Should connect properly with all CAN modules.
Hello Diakon999
Your ELM Interface is compatible with MES
Now Take a picture of the board and place the photo here.
Or look at this thread in accordance to your board
Greeting Eddy
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 11 Nov 2015, 12:07
by djakon999
Hello Alfaeddy,
I had uploaded photo earlier,
http://i68.tinypic.com/161dh21.jpg
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 11 Nov 2015, 19:18
by Alfaeddy
Hello
This side of the board brings no knowledge
Greeting Eddy
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 11 Nov 2015, 21:03
by djakon999
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 12 Nov 2015, 13:25
by m1taka
Alfaeddy wrote:
Hello M1taka
Remove the white plastic housing at 8 pin connector
including the bridge resistance should be located.
And make a new image, or rummage through this thread in accordance to your board
Greeting Eddy
Hi Eddy,
Thanks for the reply. Here are the pictures I made (I didn't actually remove the white plastic housing at 8 pin connector, because I'm not sure it will not brake, but I lifted it up a bit):
https://drive.google.com/file/d/0B8L9oy ... sp=sharing
https://drive.google.com/file/d/0B8L9oy ... sp=sharing
Is the R04 the one which should be unsoldered?
Regards, M1taka
