Multiecuscan

Hello Mitix

The lighting control is not to disable with MES.
If you are LED lights einbaust must obstruct resistance you either LEDs with CAN.
Or generally install a load resistor before the light.

Only it would be good if we order what car is knowledge itself ??

Greeting Eddy

Alfaeddy wrote:Hello Mitix

The lighting control is not to disable with MES.
If you are LED lights einbaust must obstruct resistance you either LEDs with CAN.
Or generally install a load resistor before the light.

Only it would be good if we order what car is knowledge itself ??

Greeting Eddy

thax alot

Hello, I'm trying connect my Fiat Stilo with the ELM Adaptor and I found this problem..

COMMAND: ATZ
RESPONSE:

ELM327 v1.5

>

COMMAND: ATI
RESPONSE:
ELM327 v1.5

>

COMMAND: ATE0
RESPONSE: ATE0
OK

>

COMMAND: ATL0
RESPONSE: OK

>

COMMAND: ATH0
RESPONSE: OK

>

COMMAND: ATSPC
Se excedió el tiempo de espera de la operación.

I have this adaptor





I see a 121 Resistor and I don't know if I remove it the adaptor will work fine... Can anybody help me??

Anybody can help me with this cable??

Hi everybody

I just bought an ELM 327 OBDII interface from eBay:

http://www.ebay.it/itm/181581670127?_tr ... EBIDX%3AIT

And the cables here:

http://www.ebay.it/itm/281719928580?_tr ... EBIDX%3AIT

I installed the latest FREE version of Multiecuscan (just wanted to evaluate the product, and buy it later).
My aim is to check my Alfa Mito 1.3 Mj2 95CV informations and details, and deactivate the safety belt alarm.
Once installed, I connected MES to the device via the COM3 port, but MES is not able to work with the car.

Can you help me please? Is my device a faulty-one or it is not supported at all?

You can hereafter find the log from the COM communication test.

Delce wrote:Hello, I'm trying connect my Fiat Stilo with the ELM Adaptor and I found this problem..

COMMAND: ATZ
RESPONSE:

ELM327 v1.5

>

COMMAND: ATI
RESPONSE:
ELM327 v1.5

>

COMMAND: ATE0
RESPONSE: ATE0
OK

>

COMMAND: ATL0
RESPONSE: OK

>

COMMAND: ATH0
RESPONSE: OK

>

COMMAND: ATSPC
Se excedió el tiempo de espera de la operación.

I have this adaptor





I see a 121 Resistor and I don't know if I remove it the adaptor will work fine... Can anybody help me??

Hello

Your fault indicator does not come from a bridge resistance
I assume that you have no driver or the wrong driver installed.

Do not use the driver from the CD
but also not be looking for even after the driver Windows.

Use this driver

http://www.ftdichip.com/Drivers/VCP.htm


In Stilo, the motor controller, the ABS can not be read via CAN bus
therefore you should order to be able to connect without modification.


And again, your photos are so bad that you can hardly see anything

Greeting Eddy

giefferre wrote:Hi everybody

I just bought an ELM 327 OBDII interface from eBay:

http://www.ebay.it/itm/181581670127?_tr ... EBIDX%3AIT

And the cables here:

http://www.ebay.it/itm/281719928580?_tr ... EBIDX%3AIT

I installed the latest FREE version of Multiecuscan (just wanted to evaluate the product, and buy it later).
My aim is to check my Alfa Mito 1.3 Mj2 95CV informations and details, and deactivate the safety belt alarm.
Once installed, I connected MES to the device via the COM3 port, but MES is not able to work with the car.

Can you help me please? Is my device a faulty-one or it is not supported at all?

You can hereafter find the log from the COM communication test.

Code: Select all

COMMAND: ATZ
RESPONSE: 

ELM327 v2.1

>

COMMAND: ATI
RESPONSE: ATI
ELM327 v2.1

>

COMMAND: ATE0
RESPONSE: ATE0
OK

>

COMMAND: ATL0
RESPONSE: OK

>

COMMAND: ATH0
RESPONSE: OK

>

COMMAND: ATSPC
RESPONSE: OK

>

COMMAND: ATS0
RESPONSE: OK

>

COMMAND: ATCAF0
RESPONSE: OK

>

COMMAND: ATCFC0
RESPONSE: ?

>

COMMAND: ATCRA 7B0
RESPONSE: ?

>

COMMAND: ATSH 7B0
RESPONSE: ?

>

COMMAND: ATAT1
RESPONSE: OK

>

COMMAND: ATST41
RESPONSE: OK

>

COMMAND: ATBI
RESPONSE: OK

>

WARNING: This interface is not compatible with ELM 327 1.3! Will not connect to any CAN module.

Hello

It has been written many times here, the interface with the
Version v2.1 are not compatible with MES.




Greeting Eddy

Alfaeddy wrote: Hello

Your fault indicator does not come from a bridge resistance
I assume that you have no driver or the wrong driver installed.

Do not use the driver from the CD
but also not be looking for even after the driver Windows.

Use this driver

http://www.ftdichip.com/Drivers/VCP.htm


In Stilo, the motor controller, the ABS can not be read via CAN bus
therefore you should order to be able to connect without modification.


And again, your photos are so bad that you can hardly see anything

Greeting Eddy

Hello, thanks for the help!! I installed the drivers you say but my Pc don't recognize the cable so I'll need to install the drivers that came in CD. They are called CH340, when I install these drivers my Pc recognize the cable if not it can't recognize it...

I'll try to send some best photos of the adaptor.

Here the photos with best resolution
http://i.imgur.com/Gx2izUH.jpg?1
http://i.imgur.com/yIAvEHR.jpg

The R2 Resistor is 121 maybe if the cable work I need to remove it to enter in BODY menu for activate Control Cruise

Hello Delce

Yes, R2 is the bridge resistance

But your Stilo should be able to connect to your engine control unit with this resistor.
Because of this ECU is not read via CAN bus.

Mach again a screen from the test in Multiecuscan and show your Screen

Because there is also v1.5 Interface that are not compatible with MES.
not only the v2.1 Interface

Greeting Eddy