Page 140 of 255
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 25 Aug 2014, 11:55
by Waltomatic
Alfaeddy wrote:Hello Walter
Nice to see your link now works
but I do not quite understand what you did ????
Pin 4 and 5 are always connected (mass)
[ see the picture: VAG connector only had pin 4 connected ]
Pin 15 is no longer needed since the system is outdated.
[ I don't know, only linked these like my ELM ]
the pin 15 is no longer occupied in the vehicles
[ I really don't know if the solution was pins 4-5 or 7-15 or both, only that was run after the program found both interfaces ]
But why is your Latency Time have improved ?????
[ It was change by himself, after set both interfaces ]
Greetings Eddy
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 25 Aug 2014, 13:50
by Alfaeddy
Hello Walter
Then the missing mass was the problem on pin 5 !!
One such error was ever a user ???
I've seen in about 50 KKL interface into but in all pin 4 +5 were associated
Greetings Eddy
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 25 Aug 2014, 14:17
by Waltomatic
Well, was the price for the small cost...
or...
the cost for the small price?
http://www.lightinthebox.com/kkl-vag-co ... rrency=USD
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 26 Aug 2014, 13:17
by libertyt8
Please help me. Which is this board's resistance ?
Version 1.5a usb
Thanks.
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 26 Aug 2014, 14:49
by Waltomatic
libertyt8 wrote:Please help me. Which is this board's resistance ?
Version 1.5a usb
Thanks.
Your interface not runs?
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 26 Aug 2014, 19:46
by dafe
Alfaeddy wrote:
Hi
Then you have destroyed more than the resistor of CAN bus protocol interferes
Greetings Eddy
mmhhh i don't think so but it's probably. However RIP
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 26 Aug 2014, 19:53
by Alfaeddy
Hello libertyt8
As Walter already asked?
What does not work?
Which vehicle you would like to read?
What control?
A more detailed description can help us very much to help you.
Remove the white plug housing to please the 8pin bar
and do another picture of it
Greetings Eddy
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 26 Aug 2014, 21:21
by libertyt8
1. I can't see datas which in this photo
2.I can't see like these options " Bady, Service, Other"
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 26 Aug 2014, 21:32
by Alfaeddy
hello libertyt8
Which vehicle?
And as already written, remove the white plastic base on the 8pin bar and take a picture of it
Greetings Eddy
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Posted: 26 Aug 2014, 22:34
by libertyt8
My car's 2005 Marea Liberty 1.6 16 valve
Solder how it turns out
