Re: Multiecuscan 3.3 RELEASED!!!
Posted: 19 Oct 2011, 13:26
Yani great job: thanks 
Page 2 of 3
Re: Multiecuscan 3.3 RELEASED!!!
Posted: 19 Oct 2011, 20:43
a lot of improvements
Re: Multiecuscan 3.3 RELEASED!!!
Posted: 23 Oct 2011, 09:44
Thanks !!!
Noticed that Lancia Thesis 2,4 Mjet Aisin Autom gearbox was added.
Missed this before. Will test later. Many owners complain about late up-shifting.
Try to adjust.
Keep up good work.
Noticed that Lancia Thesis 2,4 Mjet Aisin Autom gearbox was added.
Missed this before. Will test later. Many owners complain about late up-shifting.
Try to adjust.
Keep up good work.
Re: Multiecuscan 3.3 RELEASED!!!
Posted: 23 Oct 2011, 15:26
Hi,
Did reinitialisation of tranny, and shifting is now much better(sooner).
I know this can be done manually (see E-Learn Thesis) and that coolingfluid temp. as well as
tranny atf temp should be within certain limits. Now we can check both thru FES!!
So i did the reset when both temps were within range, just to be safe!!
Great, forever in your debt, Yanni !!!
Did reinitialisation of tranny, and shifting is now much better(sooner).
I know this can be done manually (see E-Learn Thesis) and that coolingfluid temp. as well as
tranny atf temp should be within certain limits. Now we can check both thru FES!!
So i did the reset when both temps were within range, just to be safe!!
Great, forever in your debt, Yanni !!!
Re: Multiecuscan 3.3 RELEASED!!!
Posted: 24 Oct 2011, 11:54
Hi,
I own an Y10 with the references below, will this new version support Bosch MA1.7 (using ELM327 V1.4a)
I've read that it supports MA1.7.3, but what about MA1.7? is it the same?
Connecting My interface using a 3pin adapter to my Y10 seems Ok as the TX and RX leds are blinking on both sides, (while they stay steady on my Xsara VTS HDi 110 with VAN protocol). I've tested V 3.2 and my Y10 is not recognized. will this 3.3 recognize it?
Y10 references:
Mode l: Y10 LXie 1.1 litre
Year: 91-95
System: Bosch MA1.7
OE Ref. No.: 0 261 200 716
VM Ref. No.: 7778785
ATP Pt. No.: XEBS0716
Many thanks for your help.
Best regards,
Olivier.
I own an Y10 with the references below, will this new version support Bosch MA1.7 (using ELM327 V1.4a)
I've read that it supports MA1.7.3, but what about MA1.7? is it the same?
Connecting My interface using a 3pin adapter to my Y10 seems Ok as the TX and RX leds are blinking on both sides, (while they stay steady on my Xsara VTS HDi 110 with VAN protocol). I've tested V 3.2 and my Y10 is not recognized. will this 3.3 recognize it?
Y10 references:
Mode l: Y10 LXie 1.1 litre
Year: 91-95
System: Bosch MA1.7
OE Ref. No.: 0 261 200 716
VM Ref. No.: 7778785
ATP Pt. No.: XEBS0716
Many thanks for your help.
Best regards,
Olivier.
Re: Multiecuscan 3.3 RELEASED!!!
Posted: 26 Oct 2011, 18:52
I completely agree. Support Fiat Brava 1.6 16V is necessary.beowolf wrote:still no support for ECU Marelli IAW 1AF for fiat brava 1.6 16V ??????? Why???? I'm ready to buy FES if u add this car. Lots of ppl will buy it I think...
Re: Multiecuscan 3.3 RELEASED!!!
Posted: 26 Oct 2011, 18:57
MA1.7.3 works only with KKL/VagCom and OBDKey 1.40.olahaye74 wrote:Hi,
I own an Y10 with the references below, will this new version support Bosch MA1.7 (using ELM327 V1.4a)
I've read that it supports MA1.7.3, but what about MA1.7? is it the same?
Connecting My interface using a 3pin adapter to my Y10 seems Ok as the TX and RX leds are blinking on both sides, (while they stay steady on my Xsara VTS HDi 110 with VAN protocol). I've tested V 3.2 and my Y10 is not recognized. will this 3.3 recognize it?
Y10 references:
Mode l: Y10 LXie 1.1 litre
Year: 91-95
System: Bosch MA1.7
OE Ref. No.: 0 261 200 716
VM Ref. No.: 7778785
ATP Pt. No.: XEBS0716
Many thanks for your help.
Best regards,
Olivier.
Re: Multiecuscan 3.3 RELEASED!!!
Posted: 28 Oct 2011, 18:39
DID YOU FIX PROBLEMS WITH DELPHY CLIMA CONTROL?
Re: Multiecuscan 3.3 RELEASED!!!
Posted: 30 Oct 2011, 02:33
Good,it works.thanks
Re: Multiecuscan 3.3 RELEASED!!!
Posted: 01 Nov 2011, 20:48
And what about with climatronic control bugs?