ECU ODOMETER raise over 100kkm after proxy

[adasch]

Hi,

before i use proxy i have odometer on 220kkm level ecu, dash etc.
after proxy ecu have 330kkm all rest still have 220kkkm
i check this on old fes too, odometer in ecu has change to 330kkm.

what do you think? about this?

cheers

p.s.
i still have problems with proxy procedure

CURRENTLY CONFIGURED CAN MODULES:
Body Computer Node (NBC)
Engine Control Node (NCM)
Electric Steering Node (NGE)
Dashboard Node (NQS)
Steering Wheel Controls Node (NVO)
Brake System Node (NFR)
Info-Telematic/Convergence Node (NIT/NCV)
Driver Door Node (NPG)
Boot Node (NVB)
Climate Control Node (NCL)
Steering Angle Sensor Node (NAS)
Passenger Door Node (NPP)
Driver Seat Node (NAG)
Passenger Seat Node (NAP)
Parking Sensor Node (NSP)
CURRENTLY AVAILABLE CAN MODULES:
Body Computer Node (NBC)
Engine Control Node (NCM)
Electric Steering Node (NGE)
Dashboard Node (NQS)
Steering Wheel Controls Node (NVO)
Brake System Node (NFR)
Info-Telematic/Convergence Node (NIT/NCV)
Driver Door Node (NPG)
Boot Node (NVB)
Climate Control Node (NCL)
Steering Angle Sensor Node (NAS)
Passenger Door Node (NPP)
Driver Seat Node (NAG)
Passenger Seat Node (NAP)
Parking Sensor Node (NSP)
CAN MODULES THAT REQUIRE EOL PROGRAMMING:
Body Computer Node (NBC)
Dashboard Node (NQS)
Climate Control Node (NCL)
Parking Sensor Node (NSP)
2012-01-15 01:07:47
CONNECTED TO:
FIAT STILO 1.9 JTD
CAN Setup / PROXI Alignment Procedure
--------------------------------------------------------------

CURRENTLY CONFIGURED CAN MODULES::
Body Computer Node (NBC):
Engine Control Node (NCM):
Electric Steering Node (NGE):
Dashboard Node (NQS):
Steering Wheel Controls Node (NVO):
Brake System Node (NFR):
Info-Telematic/Convergence Node (NIT/NCV):
Driver Door Node (NPG):
Boot Node (NVB):
Climate Control Node (NCL):
Steering Angle Sensor Node (NAS):
Passenger Door Node (NPP):
Driver Seat Node (NAG):
Passenger Seat Node (NAP):
Parking Sensor Node (NSP):
:
CURRENTLY AVAILABLE CAN MODULES::
Body Computer Node (NBC):
Engine Control Node (NCM):
Electric Steering Node (NGE):
Dashboard Node (NQS):
Steering Wheel Controls Node (NVO):
Brake System Node (NFR):
Info-Telematic/Convergence Node (NIT/NCV):
Driver Door Node (NPG):
Boot Node (NVB):
Climate Control Node (NCL):
Steering Angle Sensor Node (NAS):
Passenger Door Node (NPP):
Driver Seat Node (NAG):
Passenger Seat Node (NAP):
Parking Sensor Node (NSP):
:
CAN MODULES THAT REQUIRE EOL PROGRAMMING::
Body Computer Node (NBC):
Dashboard Node (NQS):
Climate Control Node (NCL):
Parking Sensor Node (NSP):

WARNING: This vehicle is properly configured. PROXI Alignment is not needed!
EXECUTING ADJUSTMENT...
Automatic headlights switch-on - DON'T WORK body don't see switch i auto mode - cables, signal all ok - i check this on body
Old value: Disabled
New value: Enabled
COMPLETED


EXECUTING ADJUSTMENT...
PROXI Alignment Procedure
Writing CAN configuration data ...
Writing to module: Body Computer Node (NBC) SUCCESS!
Writing to module: Dashboard Node (NQS) SUCCESS!
Writing to module: Climate Control Node (NCL) FAILED! - Unknown error
Writing to module: Parking Sensor Node (NSP) SUCCESS!
FAILED TO EXECUTE
Unknown error

of course i can connect to my climate control.

ps2
my mechanic have FES 3.3

[yani]

PROXI procedure does not change the odometer.
Also, it is simply not possible to change the odometer in engine control module using Multiecuscan.
You need flashing tools change this odometer value.

The problem with failed PROXI alignment of Stilo climate control is something that I'm trying to fix. Hope that the next version will resolve it.

[adasch]

thx for replay,

odometer can be change by add valeo parking system or switches with support rain sensor?

cheers
p.s.
in FES 3.4.2 its possible to enable rain sensor and dimmer sensor?
after install rainsenor this feature work ok, but don't work dimm sensor. Of course i have switch with auto lamps mode. but fes 3.3 don't see changing swich position on auto.

[adasch]

rain sensor work