FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

[Alfaeddy]

Hello Boblelie

https://drive.google.com/open?id=0B1IA_ ... mpYRnBlVHM

Sorry this ELM no works with MES

Greetings Eddy

Hi Eddy,

Thx for your feedback. sucks monkey balls though ....
can you recommend a elm327 clone (preferred bluetooth) that will work, or will work after some modifications?
i've ordered 3 totally different ones by now and none of them work on my alfa 159 .

Hello

This one

http://www.ebay.de/itm/152303739535?_tr ... EBIDX%3AIT

Greetings Eddy

[yavoryankov]

Hi,

I tried to read the whole thread but almost 300 pages are too much.
So please excuse me if this question has been discussed before.

I Have an Alfa 159 and i have always connected successfully with my ELM v1.4 cable to all modules - except ABS of course - for it I use VAG-Com cable with switch.

Unfortunately I changed my laptop recently and now I cannot connect to all modules, although I use the same cable, on the same car, with the same version of FES.
Now I am able to connect only to the engine and the Gearbox ( Aisin - automatic). I am not able to connect to Body or to Service, nor Parktronic or any of the doors' ECUs.

I have opened the ELM and I see that the resistor ( R04), that usually makes this problem is not placed by the producer on the first place - that is why I had no problems with my old laptop.
The only difference now is that all USB ports on mu new laptop are 3.0 - which actually should be better, as far as I know.
I am posting some images of the interface.
Can you give me any idea what to do?

IMAG0039.jpg (2.15 MiB) Viewed 8346 times

IMAG0035.jpg (1.36 MiB) Viewed 8346 times

[Alfaeddy]

Hello

This is very strange ????

At the interface it is not.
Since it has worked with your old laptop.

The bridge resistor (R4) is not available.

What driver did you use?

Please use this,
http://www.ftdichip.com/Drivers/VCP.htm


Has your laptop only 3.0 usb
Mine also has 2.0 ports

Although I do not believe this is a problem.

Make times a screen of the interface test and set this here

Greeting Eddy

[yavoryankov]

Hm,

now when you say - I remembered that I have not installed these drivers for ftdichip, but the COM port works OK - the cable is up on COM3, I have reduced the latency to 1.

The interface test runs OK - all is OK.

I will install the drivers and try again and revert. If it does not happen with these drivers, I will test also all ECUs with my VAC-COM cable.

[yavoryankov]

Hi,

I installed the drivers for FTDI chip and reinstalled the driver for the COM port. My Win 10 says that there is no need to change the driver.

I tested on car, but the situation is the same... FES says that ELM327-> ECU connection is not possible

The last resort I have is to try with my old laptop, which I reinstalled and now I have to install all the things back on it.
Here are the tests of the interface made with FES:

Code: Select all

COMMAND: ATZ
RESPONSE: 

ELM327 v1.4

>

COMMAND: ATI
RESPONSE: ATI

ELM327 v1.4

>

COMMAND: ATE0
RESPONSE: ATE0

OK

>

COMMAND: ATL0
RESPONSE: OK

>

COMMAND: ATH0
RESPONSE: OK

>

COMMAND: ATSPC
RESPONSE: OK

>

COMMAND: ATS0
RESPONSE: OK

>

COMMAND: ATCAF0
RESPONSE: OK

>

COMMAND: ATCFC0
RESPONSE: OK

>

COMMAND: ATCRA 7B0
RESPONSE: OK

>

COMMAND: ATSH 7B0
RESPONSE: OK

>

COMMAND: ATAT1
RESPONSE: OK

>

COMMAND: ATST41
RESPONSE: OK

>

COMMAND: ATBI
RESPONSE: OK

>

This interface is compatible with ELM 327 1.4! Should connect properly with all CAN modules.

This is the test for the VAG-COM cable:

Code: Select all

VagCom/KKL

Testing latency with 200 bytes of data...
Min latency: 0
Max latency: 2


Testing timers...
(The acceptable tolerance for results is ~5 ms)

System supports high resolution timer.

Testing timer with 1000 ms...
..result: 1001 ms

Testing timer with 250 ms...
..result: 251 ms

Testing timer with 750 ms...
..result: 751 ms

Testing timer with 100 ms...
..result: 101 ms

All seems OK, but I cannot connect to anythig else than the engine and gearbox, with vag-com also am able to connect to ABS
Obviously I can connect only to the modules that use the K line, the others are not reachable.

The only possible thing that might have happened, as I have not used the cable for 6 months, is that during this time I gave it to a friend of mine to use it on a BMW and to another who tried to use in on FORD and may be the cable has been damaged in any way...
Is that possible?

[Alfaeddy]

Hello

Hmm. Really difficult

As you already write try your old laptop
Of problems with Windows 10 I have not read here yet. ??

Otherwise you can only help a Mod or Admin ??

Greeting Eddy

[bigwolfys]

Hello. Who can faced with elm327? car Fiat Punto 2 1.2 v8 2000 read only engine. Where it is installed this resistor?

I understand need to unsolder the top board and see what is on the bottom?

20170227_211110.jpg (4.11 MiB) Viewed 8181 times

20170227_211124.jpg (2.86 MiB) Viewed 8181 times

20170227_211207.jpg (2.9 MiB) Viewed 8181 times

[anonimo76]

Hello !! I have to remove the resistor R2 "121"?
Thank you very much!!!


http://it.tinypic.com/r/21cw30z/9
http://i63.tinypic.com/21cw30z.jpg

[Alfaeddy]

Hello. Who can faced with elm327? car Fiat Punto 2 1.2 v8 2000 read only engine. Where it is installed this resistor?

I understand need to unsolder the top board and see what is on the bottom?

20170227_211110.jpg
20170227_211124.jpg
20170227_211207.jpg

Hello

And again, to connect to your Motorecu of the Punto, no Resistor must be removed.
Since the motor is not read via CAN bus.

If it does not work, then also with other protocols not.

The resistor of the possible CAN problems is below the first board

Greeting Eddy

[anonimo76]

Hello !! I have to remove the resistor R2 "121"?
Thank you very much!!!


http://it.tinypic.com/r/21cw30z/9
http://i63.tinypic.com/21cw30z.jpg

I have to connect to alfa mito 1.6 jtdm
Thanks