FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

[Alfaeddy]

Hello Lolo85v

What can you read on your alfa 159

ECU ?
CAN setup ?
Body Comp ?
ABS ?

On the first side on this Thread is your ELM
and i think the v1.2 Chip cant read the Protokoll ISO 15765

v1.3 an later can this Protokoll read

Greeting Eddy

[Boris]

Hello

Yes I'm 95% sure, but doing is another picture of the part with 8 pins in addition to the resistor in the red frame

Greetings Eddy

Here is the picture:

P4126247.JPG (72.8 KiB) Viewed 5894 times

[Alfaeddy]

Hello Boris

This ist a nice picture

yes , remove R6 (121) and your Interface can read CAN Bus with Multiecuscan

Red frame in the last picture


Greetings Eddy

[lolo85v]

Hello I can read that the engine

http://i74.servimg.com/u/f74/13/84/33/82/20130421.jpg

[lolo85v]

Furthermore if I me connected to the engine I is none registration(inscription) to give

http://i69.servimg.com/u/f69/13/77/86/13/sans_t10.jpg

COMMAND: ATZ
RESPONSE: ATZ



ELM327 v1.5a

>

COMMAND: ATI
RESPONSE: ATI

ELM327 v1.5a

>

COMMAND: ATE0
RESPONSE: ATE0

OK

>

COMMAND: ATL0
RESPONSE: OK

>

COMMAND: ATH0
RESPONSE: OK

>

COMMAND: ATSPC
RESPONSE: OK

>

COMMAND: ATS0
RESPONSE: ?

>

COMMAND: ATCAF0
RESPONSE: OK

>

COMMAND: ATCFC0
RESPONSE: OK

>

COMMAND: ATCRA 7B0
RESPONSE: ?

>

COMMAND: ATSH 7B0
RESPONSE: OK

>

COMMAND: ATAT1
RESPONSE: OK

>

COMMAND: ATST41
RESPONSE: OK

>

COMMAND: ATBI
RESPONSE: OK

>

WARNING: This interface is not compatible with ELM 327 1.3! Will not connect to any CAN module.

[Alfaeddy]

ello Lolo85v

Why are you still using the very old version Fiatecuscan 3.6?

try some Multiecuscan 1.3!

And with the free version you can only ECU and CAN make a connection info.
The only other controls with data base


Your interface test surprises me greatly?
because the normal manner on the interface described herein with the resistance problem pass this test without errors.

Unfortunately I can not at the moment be only the tip
try it again with MES 1.3


Greetings Eddy

[Alfaeddy]

Hello Lolo85v

I just looked again your previous posts
and once detected, the ELM is not your v1.5.
But a v1.2

And as I have already written the v1.2 does not work well with Multiecuscan!
Therefore, your incomplete test display

Buy yourself another ELM and then your connection will work.

http://www.ebay.de/itm/260754573911?ssP ... 1423.l2649



Greetings Eddy

[lolo85v]

Hello I have just made tests him(it) with the version 1.3 it is similar on previous post yes it was another elm I thus have to buy versions metal and that not function(office) always not

I is not of resistance r04 but r4.

[Boris]

Hello Boris

This ist a nice picture

I was playing with macro settings

yes , remove R6 (121) and your Interface can read CAN Bus with Multiecuscan

Red frame in the last picture

Greetings Eddy

Works OK
Thanks!!!

[lolo85v]

Photo of brooches

http://i69.servimg.com/u/f69/13/77/86/13/20130412.jpg