FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Hello Elio65
Unfortunately, the images often of poor quality, you unfortunately also
Your photo flash makes everything very dazzle
But when I look at the board, I can see I should have found the resistor.
And I marked the red
Should remove this resistor and also work with your ELM Multiecuscan
Greetings Eddy
Unfortunately, the images often of poor quality, you unfortunately also
Your photo flash makes everything very dazzle
But when I look at the board, I can see I should have found the resistor.
And I marked the red
Should remove this resistor and also work with your ELM Multiecuscan
Greetings Eddy
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Sorry Eddy,
My outside interface is as follows:
While inside is as follows:
Thanks for the help!
My outside interface is as follows:
While inside is as follows:
Thanks for the help!
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Hello Elio65
Sorry but the second images are even worse than the first!
55 kb per image are far too few
And this photo flash without
Greetings Eddy
Sorry but the second images are even worse than the first!
55 kb per image are far too few
And this photo flash without
Greetings Eddy
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Hi
it is my car OBD interface,i removed the 120ohm resistor,also i add the 560PF capcitor and 100ohm resistor on pin 6 and pin 14.but till now i can't connect to anything,Engine,ABS,Body and so on.....
would you pls tell me how can i do for it?
Thanks a lot
it is my car OBD interface,i removed the 120ohm resistor,also i add the 560PF capcitor and 100ohm resistor on pin 6 and pin 14.but till now i can't connect to anything,Engine,ABS,Body and so on.....
would you pls tell me how can i do for it?
Thanks a lot
- Attachments
-
- IMAG0640.jpg (759.53 KiB) Viewed 4757 times
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Hi,
I bought un'elm327, and when I go to read, with Fiat ECU scan, the data of ABS and airbags, I find the error that can not be read on the K-line to pins 5 and 7 ....... it seems to me;
how can I change it, I'll post pictures:
I bought un'elm327, and when I go to read, with Fiat ECU scan, the data of ABS and airbags, I find the error that can not be read on the K-line to pins 5 and 7 ....... it seems to me;
how can I change it, I'll post pictures:
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Hi Giuseppe
Which car / model / year you want to read?
And why here all have such bad pictures representing
can not see anything?
The images must have a higher resolution of at least 800 kb <
In these pictures, I can not see anything
Greetings Eddy
Which car / model / year you want to read?
And why here all have such bad pictures representing
can not see anything?
The images must have a higher resolution of at least 800 kb <
In these pictures, I can not see anything
Greetings Eddy
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
FIAT, Alfa, Lancia Group,
Fiat Stilo, and Fiat Croma
Fiat Stilo, and Fiat Croma
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
OK, I try to do the best photos.
Fiat Stilo 2005 years 1,9 MJT 120CV
Fiat Croma 2008 years 1,9 MJT 140CV
Fiat Stilo 2005 years 1,9 MJT 120CV
Fiat Croma 2008 years 1,9 MJT 140CV
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Hi Jerrywang
Your pictures are too big and have nothing to do with your interface!
Why did you set here?
800 x 600 pixels is sufficient
It is clearly not an interface
Which car / model / year you want to read??
If you still have soldered a capacitor (560 pF) and a resistor (100 ohms) to pin 6 + 14?
This is completely unnecessary, remove it again
Greetings Eddy
Your pictures are too big and have nothing to do with your interface!
Why did you set here?
800 x 600 pixels is sufficient
It is clearly not an interface
Which car / model / year you want to read??
If you still have soldered a capacitor (560 pF) and a resistor (100 ohms) to pin 6 + 14?
This is completely unnecessary, remove it again
Greetings Eddy
Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Hello Giuseppe
Please this time slowly
This ELM interface you can convert without something
on Fiat Stilo read the ECU / ABS / Steering
For the air bag you need a KKL interface
For the Fiat Croma
So you can read without a rebuild your ECU / ABS / xenon
Only for the airbag / Body Comp etc. you may need to change something on the interface.
If you get no connection to the ECU you have the settings / Com port set incorrectly
First check the time settings
Greetings Eddy
Please this time slowly
This ELM interface you can convert without something
on Fiat Stilo read the ECU / ABS / Steering
For the air bag you need a KKL interface
For the Fiat Croma
So you can read without a rebuild your ECU / ABS / xenon
Only for the airbag / Body Comp etc. you may need to change something on the interface.
If you get no connection to the ECU you have the settings / Com port set incorrectly
First check the time settings
Greetings Eddy